Cybex International 710T Treadmill User Manual


 
Re-tensioning and Re-centering the Belt — Follow the procedure below.
Tools Required
• 3/4" wrench
1. Re-tension the belt.
A. Use a 3/4" wrench to turn each bolt clockwise until the silver washers
are flush with the protruding the tab on the end caps. See Figure 1.
B. Turn the power on and press the Manual key. Press the Up Arrow to
bring the speed up to 3.5-4 mph (5.6-6.4 kph).
C. Allow the treadmill to run for a minute or two. Observe the bolts and
silver washers. If they begin to protrude or retract turn the treadmill off
and adjust the bolts. Follow the next step to be sure the belt is centered.
! CAUTION: Be careful not to over tighten the belt. Over tightening
the belt can create excessive tension on the front and
rear rollers.
! CAUTION: While centering the belt choose one bolt to adjust. Do not
adjust both bolts.
2. Re-center the belt.
A. With the treadmill running at 5 mph (8 kph) observe the running belt. If
the belt tracks off center to the right or left the deck will become
exposed. Use a 3/4” wrench to tighten the rear roller bolt on the side of
the treadmill toward which the belt is moving. For example: If the belt
moves to the right and the deck becomes exposed on the left, use a
wrench to tighten the bolt on the right side of the frame, tighten about
1/2 of a turn (clockwise) and wait 30 seconds. If the belt does not move
back to the center of the treadmill, make another adjustment to the
Cybex 710T Treadmill Owner’s Manual
Page 4-3
2
Technical Specifications
Specifications . . . . . . . . . . . 2-1
3 Operation
Quick Operation Guide . . . . 3-1
Detailed Operation Guide . . 3-1
Stopping the Treadmill. . . . . 3-3
Control During Operation . . 3-4
Data Readouts. . . . . . . . . . . 3-5
Selecting Programs
& Options . . . . . . . . . . . . . 3-6
Displaying Heart Rate . . . . . 3-6
Use of Programs . . . . . . . . . 3-7
Manual Mode . . . . . . . . . . . 3-8
P1 - Fitness Test Program. . 3-8
P2 - Weight Loss Program 3-10
P3 - Cardiovascular Program 3-12
P4 - Speed Challenge
Program . . . . . . . . . . . . . 3-14
P5 - Express Program. . . . 3-16
P6 - Hill Interval Program . 3-17
P7 - Speed Interval
Program . . . . . . . . . . . . . 3-18
P8 - Pike’s Peak Program . 3-19
P9 - River Run Program . . 3-20
P10 - 5 Kilometer Program 3-21
P11 - Demonstration
Program . . . . . . . . . . . . . 3-22
P101-P110 - Saved
Program . . . . . . . . . . . . . 3-22
Workout Tips. . . . . . . . . . . 3-24
4 Preventive Maintenance
Regular Maintenance
Activities. . . . . . . . . . . . . . 4-1
Cleaning Your Treadmill. . . . 4-1
Running Belt Maintenance . 4-2
Other Preventive
Maintenance . . . . . . . . . . . 4-6
Service Schedule . . . . . . . . . 4-7
Log Sheet. . . . . . . . . . . . . . . 4-8
5 Setup & Assembly
Quick Setup . . . . . . . . . . . . 5-1
Choosing & Preparing a Site 5-1
Electrical Power
Requirements. . . . . . . . . . 5-3
Unpacking. . . . . . . . . . . . . . 5-3
Assembling the Treadmill. . . 5-4
Testing the 710T Operation. 5-9
Setting Operation Options. 5-10
6 Customer Service
Contacting Service . . . . . . . 6-1
Serial Number & Voltage . . . 6-1
Warranty . . . . . . . . . . . . . . . 6-1
Return Material Authorization . .
(RMA) . . . . . . . . . . . . . . . . 6-4
Damaged Parts . . . . . . . . . . 6-4
Ordering Parts. . . . . . . . . . . 6-5
7 Service
Service Instruction . . . . . . . . 7-1
Motor Brushes. . . . . . . . . . . 7-1
Motor Current & Voltage . . . 7-4
Running Belt & Deck . . . . . . 7-7
Drive Belt. . . . . . . . . . . . . . . 7-9
Figure 1
Bolts
Protruding Tabs
Top View