Filter
Top Products
Effect Guide
98
026: Tube Pre (Tube PreAmp
Modeling)
Thiseffectsimulatesatwo‐stagevacuumtubepreamp.You
canmakeindividualsettin gsfortwovacuumtubes
connectedinseries.Thisletsyoucreatethewarmsound
typicalofvacuumtubes.
Saturation [%]
Withhighersettingsofthisvalue,thewaveformwillchange
athighgainlevels,tendingtocausedistortion.Lower
settingsofthisvaluewillproducelinearresponse.
Tube1 Bias
Thisexpressestheeffectthatchangesinvacuumtubebias
haveonthedistortionofthewaveform.Highersettingsof
thisvaluewillproducedistortionevenatlowgainlevels.
Sincethiswillalsochangetheovertonestructure,youcan
useittocontrolthetonalcharacter.
Tube1 Phase
WiththeWetInvertsetting,thephaseofthesignalwillbe
invertedbetweenstage1andstage2.Since“Bias”isapplied
totheinvertedsignalinstage2,thiswillchangethetonal
character.
027: St.TubPre
(Stereo Tube PreAmp
Modeling)
Thisisastereovacuumtubepreampsimulator(See“026:
TubePre(TubePreAmpModeling)”onpage 98 .).
028: Mic Model (Mic Modeling +
PreAmp)
Thiseffectsimulatesamicandvacuumtubepreamp.You
canchoosefromvarioustypesofmicandpositionstocreate
differingsonicch aracters.
Full
parameter
Quick
parameter
Value Explanation
Tube1
Low Cut [Hz]
T1 L[Hz]
Thru,
21...8.00k
Sets the cutoff
frequency for the low
cut filter of stage 1
Tube1
High Cut
[Hz]
T1 H[Hz]
53...20.00k,
Thru
Sets the cutoff
frequency for the high
cut filter of stage 1
Tube1
Gain [dB]
T1 G[Hz] –24.0...+24.0
Sets the input gain for
stage 1
Tube1
Saturation
[%]
T1 Saturat 0...100
Sets the input/output
response for stage 1
p.98
Tube1 Bias T1 Bias 0...100
Sets the bias voltage
for stage 1 p.98
Tube1 Phase T1 Phase
Normal,
Wet Invert
Turns phase reversal
on/off p.98
Tube2
Low Cut [Hz]
T2 L[Hz]
Thru,
21...8.00k
Sets the cutoff
frequency for the low
cut filter of stage 2
Tube2
High Cut
[Hz]
T2 H[Hz]
53...20.00k,
Thru
Sets the cutoff
frequency for the high
cut filter of stage 2
Tube2
Gain [dB]
T2 G[Hz] –24.0...+24.0
Sets the input gain for
stage 2
Tube2
Saturation
[%]
T2 Saturat 0...100
Sets the input/output
response for stage 2
p.98
Tube2 Bias T2 Bias 0...100
Sets the bias voltage
for stage 2 p.98
Tube2
Output Level
[dB]
Lvl [dB] –48.0...+0.0 Sets the output level
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amount –100...+100
Sets the modulation
amount for Wet/Dry
+
Tube Pre Amp1 Tube Pre Amp2
Left
Right
Wet / Dry
Output Level
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Invert
-
Mic/Pre Amp - Saturation
In
Out
Saturation = 0
Saturation = 50
Saturation = 100
Bias = 0
Full
parameter
Quick
parameter
Value Explanation
Mic Type Mic
Vintage
Dynamic,
Multi
Condenser,
Percussion
Condenser,
Drums Dynamic,
Vocal Dynamic,
Multi Dynamic,
Vocal
Condenser,
Vocal Tube,
Kick Dynamic
Selects the type of
mic
Mic Position Mic Posit
Close, On,
Off, Far
Sets the mic
placement distance
p.99
Tube
Low Cut [Hz]
T L[Hz]
Thru,
21...8.00k
Sets the frequency of
the low cut filter
In
Out
Satulation = 50
Bias = 0
Bias = 50
Bias = 100
Mic/Pre Amp - Bias
Left
Right
Wet / Dry
Output Level
Wet / Dry
Stereo In - Stereo Out
Tube Pre Amp1 Tube Pre Amp2
Tube Pre Amp1 Tube Pre Amp2
Left
Right
Wet / Dry
Wet / Dry
–
+
–
+
Invert
+
Tube Pre AmpMic Simulation
Left
Right
Wet / Dry
Output Level
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out