CONTROL MODULE PIN OUT INFORMATION
BODY PROCESSOR MODULE
Description
Active
WASHER FLUlD LEVEL SENSOR
VARIABLE INTERMlrrENTWlPE REOUEST
IGNITION
SWITCHED
GROUND
SIDE LAMP REQUEST
POWER WASH RELAY ACT,“ATE
WIPER FAST, SLOW RELAY ACT,“ATE
WINSHIELD WASHER PUMP KT,“ATE
FAST WIPE SPEED REQUEST
PROGRAMMED WASH REOUEST
WIPER RUN, STOP RELAY ACTIVATE
WIPER MOTOR PARK SWliCH STATUS
BATrERY SUPPLY VOLTAGE
SLOW, FLICK WIPE REa”EST
BATERY SUPPLY VOLTAGE
GROUND IFULL)
GROUND
GROUND
GROUND
GROUND IFAST)
!3+
GROUND
GROUND iMOMENTARY,
GROUND
GROUND IPARKED)
Bc
GROUND
B+
Inactive
ST IEMPTY)
COMPONENTS
Component
BODY PROCESSOR MODULE
Connector / Type / Color
FC15,14~WAYAMP EEEC, GREY
Location I Access
BULKHEAD, BEHIND GLOVE BOX
FUSE BOX-ENGINE COMPARTMENT
LlGHTlNG STALK iCOLUMN SWlTCHGEARi
POWER WPlSH PUMP
ST19, EYELET
SC?, 10.WAY MULTILOCK 070 lYELLOW
COLUMN SWITCHGEAR HARNESS,
ADJACENTTO STEERING COLUMN MOTOR
Em, Z-WAY REINSHAGEN, VOLKSWAGEN, BLACK
RIGHT FRONT OUARTER PANEL l WASHER FLUID CONTAINER
WASH /WIPE STALK iCOLUMN SWITCHGEAR,
SC,, I*-WAY M"LTlLOCK 070 I WHiTE
COLUMN SWITCHGEAR HARNESS,
ADJACENTTOSTEERING COLUMN MOTOR
RELAYS
Relay
WIPER RUN, STOP RELAY
WIPER FAST, SLOW RELAY
POWERWASH RELAY
Case Color
BLACK
BLACK
BROWN
Connector / Color
LS,, , BLACK
LS11, BLACK
BUS
Location / Access
ENGINE COMPARTMENT FRONT RELAYS, ENGlNE COMPARTMENT
ENGINE COMPARTMENT FRONT RELAYS, ENGlNE COMPARTMENT
RELAY ~$4, ENGINE COMPARTMENT FUSE BOX: ENGINE COMPARTMENT
HARNESS-TO-HARNESS CONNECTORS
Connector
EM3
EMSl
FC5
LS3
Location I Access
PASSENGER ‘K POST, LOWER ‘A’ POST FlNlSHER
ENGlNE CDMPARIMENT,ADJACENTTOABS PUMP
BELOW DRIVER SIDE AIR VENT, COIN TRAY
LH ‘A, POST, LOWER ‘A’ POST FiNlSHER
GROUNDS
Ground
EM17
FC17R
LS18R
LSlPL
Location / Type
EYELET
iSINGLE,
- EMS BULKHEAD
GROUND
STUD
EYELET iPAIR -EMS BULKHEAD GROUND STUD
EYELET iPAIR - LH FORWARD GROUND STUD
EYELET (PAIRI - RH FORWARD GROUND STUD
CONTROL MODULE PIN OUT INFORMATION (FOLD OUT PAGE)
+
The following symbols are used to represent values for Control Module Pin Out data:
I
Input
D Serial and encoded communications
0 output
B+ Battery voltage
C CAN (Network)
KHz Frequency x 1000
SG Signal Ground
V Voltage (DC)
MS Milliseconds
S
SCP Network
Hz Frequency
MV Millivolts
CAUTION: The information on this data page is furnished to aid the user in understanding circuit operation. THIS INFORMATION SHOULD BE USED FOR REFERENCE ONLY.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit connections made and all
components connected and fitted.
“Active” means a load is applied or a switch is ON; “Inactive” means a load is not applied or a switch is OFF.
REFER TO THE FRONT OF THE BOOK FOR ILLUSTRATIONS DETAILING THE LOCATION AND IDENTIFICATION OF COMPONENTS. RELAYS,
CONNECTORS, HARNESSES, GROUNDS, VEHICLE CONTROL MODULES AND CONTROL MODULE PINS.
