Filter
Top Products
8
OWNER'S MANUAL • T50
will remain in the meter's memory until replaced
with a new one.
4. Press Enter and set the user weight using the
arrow keys. Press Enter again to confi rm your
selection The setting will remain in the meter's
memory until replaced with a new one.
5. Press Start. The exercise begins and the belt
starts moving.
6. You can scale the the profi le speed level up and
down at 5% steps using the arrow keys.
7. Press Stop/Pause and the treadmill stops and
moves into waiting state for 5 minutes. You can
restart the interrupted exercise by pressing the Start
key within 5 minutes. Press Stop/Pause twice to
end your exercise. Keep the Stop key pressed down
for 2 seconds to reset the meter. The meter then
switches to its initial state.
If the profi le duration and user weight do not
need to be adjusted, you can start the exercise by
selecting the Hill profi le you want and pressing
Start.
MAINTENANCE
The equipment is safe to use only when
periodically maintained and inspected for faults
and wear.
CAUTION! Do not attempt any
servicing or adjustment other than those described
in this manual. Any other servicing must be
performed by an authorized service representative.
Check the tightness of all fi xing screws once a year.
Do not overtighten. Defective components must
be immediately replaced; the equipment must not
be operated with any defective components.
LUBRICATING THE RUNNING DECK
Lubrication is the most important service activity
for the treadmill. This is absolutely essential, if the
friction of the running deck increases noticeably
or the motor begins to heat up; increased friction
is indicated by jerky movement of the belt.
Insuffi cient lubrication will cause the belt, running
deck and motor to wear out and break. The need
for re-lubrication depends to a great extent on the
running styles and weight of the user: heavy user
weight and slow speed put particular strain on the
device and therefore demand greater lubrication.
The running deck requires periodic lubrication.
With average usage (30 minute workout session 3
times a week), lubricate every four to six months.
You may adjust the timing of the lubrication based
on the intensity of the treadmill use level. To check
the lubrication level, simply lift the running belt,
and put your hand as far into the center of the
belt as you can reach. If your hand shows signs of
lubricant (some wetness), then it does not need
additional lubrication. If the board feels dry and
there is very little evidence of lubricant on your
hand, then additional lubrication should be added
as instructed:
1. Stop running belt so belt seam is located on the
top and in the center of the deck.
2. Insert nozzle into spray head of lubricant can.
3. Lift running belt.
4. Position nozzle between the belt and the board
approximately 200 mm (8") from the front of the
treadmill.
5. Apply T-Lube from the front to the rear of the
treadmill on each side of the treadmill. Try to reach
the spray as far into the center of the running deck
as possible.
6. The treadmill is instantly ready for use.
NOTE! Lubricate your treadmill only with T-Lube
lubricant. Contact your local Tunturi distributor
for supplies of T-Lube.
CLEANING THE TREADMILL
Wipe the treadmill surfaces, especially the
handlebars and meter from dust with a damp cloth
or towel. Do not use solvents. Use a small vacuum
nozzle to carefully vacuum around all visible
components (belt, running deck, side rails etc.).
To clean the underside of the treadmill, lift the
running deck to the storage position.
NOTE! Also keep the area near the treadmill clean.
While in use, the treadmill gathers dust that may
cause problems in the operation of the equipment.
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually
needed, provided
•
the treadmill is placed on an even, solid
and horizontal surface and the belt is correctly
tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to
one side due to the user's running style (e.g. more
weight on one foot). The alignment of the belt is
adjusted by turning the two bolts at the back of the
treadmill.
Align the belt according to the following
instructions:
1. Turn the power switch on and increase the
treadmill's speed to 5 km/h (3 mph).
2. If the belt drifts to the left, turn the left
adjustment bolt 1/4 turn clockwise and the right
adjustment bolt 1/8 turn anti-clockwise. If the belt
drifts to the right, turn the right adjustment bolt
1/4 turn clockwise and the left adjustment bolt 1/4
turn anti-clockwise.
3. If the belt remains centered the adjustment is
correct. If not, continue to make small adjustments
as above until the belt is correctly aligned. If the
T50_manual.indd 8T50_manual.indd 8 3.8.2005 11:24:103.8.2005 11:24:10