Filter
Top Products
12
OWNER’S MANUAL
•
T90
unnecessary to take the whole device in for repair,
as it’s usually sufficient to replace the defective
part. Always give the model, serial number of
your equipment and in case of malfunctions also
conditions of use, nature of malfunction and any
error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and
ready the treadmill for normal operation again. If
after you have reset the treadmill by turning the
power switch off and on again, and the treadmill
is still not operational, contact your local Tunturi
dealer for service.
If you require spare parts, always give the model,
serial number of your equipment and the spare part
number for the part you need. The spare part list
is at the back of this manual. Use only spare parts
mentioned in the spare part list.
ERROR CODES
The user interface will display information about
operational faults.
SYSTEM CHECK FAILED - Possible motor controller
fault. Turn the power switch off, wait 1 minute and
turn the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR - Call the dealer for service.
MOTOR SPEED ERROR - Ensure correct usage of
the treadmill. Do not push the belt with your feet.
Turn the power switch off, wait 1 minute and turn
the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
MOTOR OVERLOAD - Ensure correct usage of the
treadmill. Do not brake the belt. Turn the power
switch off, wait 1 minute and turn the power switch
on again. If treadmill recovers to normal operation,
you may continue to use the treadmill. Ensure the
lubrication is sufficient, re-lubricate the running
deck if needed. Otherwise, call the dealer for service.
LIFT MOTOR ERROR - Call the dealer for service.
LIFT MOTOR OVERLOAD - Ensure correct usage
of the treadmill. Do not overload the lift motor
by continuously changing the elevation. Turn the
power switch off, wait 1 minute and turn the power
switch on again. The lift motor will be automatically
calibrated when the power switch is turned on. If
treadmill recovers to normal operation, you may
continue to use the treadmill. Otherwise, call the
dealer for service.
MAINTENANCE CODE
CHECK LUBRICATION. Ensure the lubrication is
sufficient, re-lubricate the running deck only if
needed. Remove the code by pressing the ENTER
key twice.
MOVING AND STORAGE
Move the T90 treadmill according to the following
instructions: turn off the power switch and unplug
the power cord from the wall and the treadmill.
Stand behind the treadmill and take hold of the
aluminium profile at the rear end of the treadmill.
Tilt the rear end of the equipment so that it rests on
the transportation wheels, and move the equipment
by wheeling. Lower the treadmill carefully onto the
floor.
NOTE! Transport the treadmill with extreme caution
over uneven surfaces, for example over a step. The
treadmill should never be transported upstairs using
the wheels over the steps, instead it must be carried.
We recommend that you use a protective base when
transporting the equipment. The running belt needs
to be realigned and centered after moving.
To prevent malfunctioning of the treadmill, store it
in a dry place with as little temperature variation as
possible, protected against dust. Always unplug the
treadmill from the electrical outlet when not in use.
TECHNICAL DATA
Length ............................... 214 cm
Height ................................ 143 cm
Width ................................. 91 cm
Weight ................................ 126 kg
Running surface ............. 52 x 158 cm
Speed ................................. 0,3-18,0 km/h / 0,2-11 mph
Elevation range .............. 0-12 %
Motor ................................. 3,5 HP
T90 treadmill meets the requirements of the EU’s
EMC Directives on electromagnetic compatibility
(89/336/EEC) and electrical equipment designed for
use within certain voltage limits (73/23/EEC). This
product therefore carries the CE label. T90 treadmill
meets EN precision and safety standards (Class SA,
EN-957, parts 1 and 6).
Due to our continuous policy of product
development, Tunturi reserves the right to change
specifications without notice.
CAUTION! The instructions must be followed
carefully in the assembly, use and maintenance
of your equipment. The warranty does not cover
damage due to negligence of the assembly,
adjustment and maintenance instructions described
herein. Changes or modifications not expressly
approved by Tunturi Oy Ltd will void the user’s
authority to operate the equipment!
We wish you many enjoyable trainings with your
new Tunturi training partner!