14
OWNER’S MANUAL
•
T80/F T85/F
1. Increase the treadmill’s speed to 5 km/h (3 mph).
2. Turn both adjustment screws an equal amount, ¼
turn clockwise.
3. Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill).
If the belt slips, turn another ¼ turn and repeat the test.
When braking heavily the belt may slip. If the belt keeps
slipping despite repeated adjustments, please contact
your local Tunturi dealer.
MALFUNCTIONS
NOTE! Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it’s unnecessary
to take the whole device in for repair, as it’s usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and ready
the treadmill for normal operation again. If after you
have reset the treadmill by turning the power switch off
and on again, and the treadmill is still not operational,
contact your local Tunturi dealer for service.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.
ERROR CODES
The user interface will display information about
operational faults.
SYSTEM CHECK FAILED. Possible motor controller
fault. Turn the power switch off, wait 1 minute and
turn the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR. Call the dealer for service.
MOTOR SPEED ERROR. Ensure correct usage of
the treadmill. Do not push the belt with your feet.
Turn the power switch off, wait 1 minute and turn the
power switch on again. If treadmill recovers to normal
operation, you may continue to use the treadmill.
Otherwise, call the dealer for service.
MOTOR OVERLOAD. Ensure correct usage of the
treadmill. Do not brake the belt. Turn the power switch
off, wait 1 minute and turn the power switch on again.
If treadmill recovers to normal operation, you may
continue to use the treadmill. Ensure the lubrication
is sufficient, re-lubricate the running deck if needed.
Otherwise, call the dealer for service.
LIFT MOTOR ERROR. Call the dealer for service.
LIFT MOTOR OVERLOAD. Ensure correct usage
of the treadmill. Do not overload the lift motor by
continuously changing the elevation. Turn the power
switch off, wait 1 minute and turn the power switch on
again. If treadmill recovers to normal operation, you
may continue to use the treadmill. Otherwise, call the
dealer for service.
MOVING AND STORAGE
Turn off the power switch and unplug the power cord
from the wall and the treadmill. Take hold of the
aluminium profile at the rear end of the running base
and lift the running base up. Press the horizontal bar
in the folding frame with your foot to lock the running
base to the lower frame. NOTE! The gas spring is
designed to make lifting the running base easier. Always
remember to ensure that the running base is locked in
the storage position.
Move the T80F / T85F treadmill according to the
following instructions: turn the transportation wheels
located at the front end of the treadmill so that
they point forward, and push the equipment on the
transportation wheels. If you wheel the equipment
sideways, there is no need to turn the transportation
wheels. Once you have moved the treadmill, return
the transportation wheels to their sideways position.
To release the running base lock, tilt the running base
slightly forward while pushing the locking levers in
the lower frame to the side with your foot. Lower the
treadmill carefully onto the floor.
Move the T80 / T85 treadmill according to the
following instructions: stand behind the treadmill and
take hold of the aluminium profile at the rear end of
the treadmill. Tilt the rear end of the equipment so
that it rests on the transportation wheels, and move the
equipment by wheeling. Lower the treadmill carefully
onto the floor.
NOTE! Transport the treadmill with extreme caution
over uneven surfaces, for example over a step. The
treadmill should never be transported upstairs using
the wheels over the steps, instead it must be carried.
We recommend that you use a protective base when
transporting the equipment. The running belt needs to
be realigned and centered after moving.
To prevent malfunctioning of the treadmill, store it in a
dry place with as little temperature variation as possible,
protected against dust. Always unplug the treadmill
from the electrical outlet when not in use.
T80_T85_manual.indd 14 23.3.2004, 15:56:37