Filter
Top Products
10
OWNER’S MANUAL
•
T80/F T85/F
3. Press START. The exercise begins and the belt starts
moving.
4. Use the speed control keys or PSC to adjust the
speed. Pressing SELECT during the exercise will display
speed and elevation profiles for the exercise.
5. Press STOP and the treadmill stops and moves
into waiting start for 5 minutes. You can restart the
interrupted exercise by pressing the START key within
5 minutes. Press STOP twice to end your exercise. Keep
the STOP key pressed down for 2 seconds to reset the
meter. The meter then switches to its initial state.
6. Once the profile has been completed, the treadmill
will automatically stop. You can save your workout in
the meter’s memory (see Memory Function).
C. Heart rate controlled HRC profiles (5-8) are heart
rate controlled exercise profiles with different effort
levels that allow you to set the duration of the exercise.
The heart rate controlled profiles always require the
use of a heart rate belt. If heart rate measurement is
not working correctly, the error message CHECK
TRANSMITTER will be displayed. You should
then make sure that you have properly followed the
instructions on the use of the heart rate belt.
1. Press SELECT until the signal light shows next to the
profile (5-8) you want. Press ENTER to confirm your
selection.
2. Select the HRC mode with the arrow keys. Press
ENTER to confirm your selection.
3. Press SELECT to move to profile duration (time /
distance) setting. The previous duration set is shown on
the display. Use the SELECT key to alternate between
different setting values. You can change the value using
the arrow keys (limit 10 minutes (0:10) – 3 hours (3:
00), adjusting at 5 minute steps / 3 km – 42 km,
adjusting at 1 km steps). Press ENTER to confirm your
selection.
4. Press START. The exercise begins and the belt starts
moving.
5. You can scale the profile speed level up and down at 5
% steps using the arrow keys.
6. Press STOP and the treadmill stops and moves
into waiting start for 5 minutes. You can restart the
interrupted exercise by pressing the START key within
5 minutes. Press STOP twice to end your exercise. Keep
the STOP key pressed down for 2 seconds to reset the
meter. The meter then switches to its initial state.
7. Once the profile has been completed, the treadmill
will automatically stop. You can save your workout in
the meter’s memory (see Memory Function).
PROFILES
(profile figures are at the back fold of the manual)
PROFILE 1 (Hill Walk). This profile is based on regular
changes in elevation, combined with a fairly steady,
brisk walking pace. The profile is suited to beginners
and active walkers. The default values are preset to an
average speed of 5.2 km/h and a top speed of 5.8 km/h,
with an average elevation of 2.7%.
PROFILE 2 (Hill Jog). This profile is based on irregular
changes in elevation, combined with a fairly steady, light
jogging pace. The profile is suited to beginners as well as
to those who want to maintain their fitness. The default
values are preset to an average speed of 6.9 km/h and
a top speed of 7.2 km/h, with an average elevation of
1.9%.
PROFILE 3 (Hill Run). This profile is based on a
consistent, low elevation, combined with a brisk
running pace with regular variation. The profile is suited
to active runners. The default values are preset to an
average speed of 11.6 km/h and a top speed of 12.5
km/h, with an average elevation of 1.8%.
PROFILE 4 (Rolling Hills). A distance profile where you
can set the distance to be covered in kilometres. The
profile is specifically designed for regular training, but
also allows for varied routines in fitness training. The
maximum distance is 42 km, with the default value
preset to 3 km, adjusting at 1 km steps. The profile
features interval type elevation settings, with an
average elevation of 2.4%.
PROFILE 5 (Fatburner 1). A heart rate profile with a
low level of effort, based on a regular rise and fall in the
heart rate. The profile is suited to weight control. The
default values are preset to an average heart rate of 114
bpm and a maximum heart rate of 125 bpm.
PROFILE 6 (Fatburner 2). A heart rate profile with
a medium level of effort, based on an interval type
rise and fall in the heart rate. The profile is suited to
fitness training and weight control. The default values
are preset to an average heart rate of 122 bpm and a
maximum heart rate of 136 bpm.
PROFILE 7 (Cardio). A heart rate profile with a medium
level of effort, based on a regular rise and fall in the
heart rate. The heart rate level remains at around 130-
140 bpm almost throughout the entire exercise. The
profile is ideal for fitness training. The default values
are preset to an average heart rate of 129 bpm and a
maximum heart rate of 145 bpm.
PROFILE 8 (Fit). A heart rate profile with a high level of
effort, based on a regular rise and fall in the heart rate.
The heart rate level remains at around 135-145 bpm
almost throughout the entire exercise. The profile is
suited to demanding fitness training and improvement.
The default values are preset to an average heart rate of
133 bpm and a maximum heart rate of 150 bpm.
POSITION SPEED CONTROL (PSC)
Position Speed Control (PSC) allows you to adjust
running track speed by changing your position on the
track. Move to the front of the track and it accelerates,
and as you move back the track itself slows down. When
you are walking or running in the middle section of the
track the speed stays steady.
T80_T85_manual.indd 10 23.3.2004, 15:56:35