Filter
Top Products
GB
OWNER’S MANUAL
•
T60
7
length of the safety key wire so that it will be detached
from the console, if you move too far back.
NOTE! If you are exercising with PSC, there must not
be another heart rate transmitter near the treadmill
(minimum distance 2 m); the simultaneous signals of
two transmitters endanger user safety by interfering with
the PSC.
PSC SETTINGS
PSC settings should be done with the treadmill at a
complete stop.
1. Start the use of PSC by setting the speed zone limits.
Press the PSC key.
2. Depending on the previous settings, either PSC ON
or PSC OFF will be displayed. Use the arrow keys to
change the setting to PSC ON and press ENTER.
3. PRESS ENTER TO CALIBRATE PSC OR START
TO EXIT will be displayed. Position yourself in the
middle of the track. The acceleration zone begins
approximately 10 cm ahead of the measurement point,
while the deceleration zone begins approximately 20 cm
behind the measurement point. Press ENTER and the
text PLEASE WAIT 8 will be displayed. The console
will now measure your distance on the basis of the heart
rate signal. Measurement takes 8 seconds, and after that
CALIBRATION READY PRESS START is displayed.
4. If the console cannot receive the heart rate signal
or there are problems in measuring the distance, the
console will return to the CALIBRATE display. In case
of such an error, the text CHECK TRANSMITTER
is displayed. You should then make sure that you have
properly followed the instructions on the use of the
heart rate belt.
If the speed zone limits are suitable for you, the next
time you start exercising you can start PSC just by
selecting PSC ON and pressing ENTER and START,
and then select the desired training mode. If you want
to change the speed zone limits, repeat steps 1-4 and
move to a more suitable position on the track before the
measurement.
TRAINING WITH PSC
1. Select Manual exercise, Rolling Hills profile, a
condition test or the standard heart rate exercise with
automatic elevation adjustment. In these exercises you
can adjust the track speed with PSC. The PSC signal
light indicates that the feature is in operation. T60 is
equipped with three PSC signal lights that show in
which speed zone you are currently running (Rabbit
= speed increases, - = constant speed, Turtle = speed
decreases).
2. Start the selected exercise by pressing the START
key, and adjust track speed by moving forward or back
on the track. Please note that the speed adjustment
keys (Turtle/Rabbit) are also in operation during a PSC
exercise. NOTE! If you have not tried the PSC feature
before, we recommend you start at slow speed.
CHOOSING AN EXERCISE
Press SELECT until the signal light indicates the desired
exercise. You can choose between:
1. Manual exercise in which you adjust both speed and
elevation yourself during the exercise.
2. Heart rate controlled HRC exercise in which the
treadmill adjusts the speed / elevation automatically,
so that your heart rate stays at the level set. You always
need to wear a heart rate belt while doing HRC
exercises.
3. Fitness tests feature with two test options: a 2-
kilometre walking test and a 12-minute Cooper run test.
4. Preset exercise profile in which speed/elevation or
heart rate level vary according to the preset program.
MANUAL EXERCISE
QUICK START
1. Manual exercise is the treadmill default setting. You
can start the exercise directly by pressing the START
key. The belt starts moving at 1,5 km/h / 1,0 mph.
STARTING WITH THE USER DETAILS SETUP
2. If you want to use user details or save your workout,
set your user details or select your user code (1-4). Press
START to confirm your selection.
3. Press SELECT until the signal light shows next to the
Manual text.
4. Press START. The belt starts moving at 1,5 km/h
/ 1,0 mph. Use the Rabbit/Turtle keys or the PSC
function to adjust the speed and the elevation control
keys to adjust the elevation.
5. Press START. The belt starts moving at 1,5 km/h
/ 1,0 mph. Use the Rabbit/Turtle keys or the PSC
function to adjust the speed and the elevation control
keys to adjust the elevation.
6. Press STOP and the treadmill stops and moves
into waiting state for 5 minutes. You can restart the
interrupted exercise by pressing the START key
within 5 minutes. You can use the waiting state to save
your workout in the console’s memory (see Memory
Function). Press the STOP key twice to end exercising
and display feedback on your workout. The console
then switches to its initial state.
HEART RATE CONTROLLED
EXERCISE
Heart rate controlled exercises enable training at a
selected heart rate level. Heart rate controlled exercises
always require the use of a heart rate belt. If heart rate
measurement is not working correctly, the error message
CHECK TRANSMITTER will be displayed. You
should then make sure that you have properly followed
the instructions on the use of the heart rate belt.
1. If you want to use user details or save your workout,
set your user details or select your user code (1-4). Press
START to confirm your selection.
2. Press SELECT until the signal light shows the HRC
text. Press ENTER to confirm your selection.
3. Select the HRC mode with the arrow keys:
T60_manual_uusi versio_j.indd 7T60_manual_uusi versio_j.indd 7 25.10.2006 13:33:5325.10.2006 13:33:53