Filter
Top Products
GB
OWNER’S MANUAL
•
T60
11
profile with a new one. The display then prompts you
to confirm (REPLACE OWN 1-5). Press ENTER to
confirm your selection: your workout is now saved to
the desired slot.
4. SAVED AS OWN 1-5 is displayed to confirm your
save. The console will automatically switch to its initial
state.
NOTE! A total of 30 speed or elevation changes can
be saved in each profile. To save a profile, you need to
exercise for 10 minutes or more.
USING YOUR OWN PROFILE:
1. Select your user code.
2. Press MEM.
3. Press SELECT until the signal light indicates the
desired own profile (-1-5 MEMORY). Press ENTER
to confirm your selection. Select RERUN (to use
the profile without adjustments) or RACE (to use
the profile as a basis for the Race function) with the
SELECT key.
4. Press ENTER to confirm your selection.
5. Press START to begin the profile.
6. The RERUN function allows you to scale your own
profile and save the changes.
RACE FUNCTION
To race against a previously saved speed/elevation profile
exercise, select RACE in the Own Profile menu. The
goal is to complete the profile as fast as possible.
1. Press START. The exercise begins and the belt starts
moving.
2. Adjust the speed according to your fitness level either
manually or using the PSC function.
3. The console display shows information on profile
progress and any changes ahead, and also shows
how your performance compares to the previously
saved session: when you fall behind your previously
saved session, the display will read “YOU ARE x.xx
BEHIND”. When you are ahead of your previously
saved session, the display will read “YOU ARE x.xx
AHEAD”.
4. Once the profile has been completed, the treadmill
will automatically stop. You can save your workout in
the console’s memory (see Memory Function).
MAINTENANCE
The equipment is safe to use only when periodically
maintained and inspected for faults and wear. Do not
attempt any servicing or adjustment other than those
described in this manual. Any other servicing must
be performed by an authorized service representative.
Check the tightness of all fixing screws once a year.
Do not overtighten. Defective components must be
immediately replaced: the equipment must not be
operated with any defective components.
CLEANING AND LUBRICATING THE TREADMILL
FAILURE TO LUBRICATE YOUR TREADMILL MAY
INVALIDATE THE PRODUCT’S WARRANTY!
Wipe the treadmill surfaces, especially the handlebars
and console from dust with a damp cloth or towel.
Do not use solvents. Use a small vacuum nozzle to
carefully vacuum around all visible components (belt,
running deck, side rails etc.). Also keep the area near
the treadmill clean. While in use, the treadmill gathers
dust that may cause problems in the operation of the
equipment.
In average domestic use (a maximum of 60 minutes a
day), you should check the lubrication once a month
– however, lubricate the belt only if needed. In more
demanding use, the lubrication needs be checked at
shorter intervals. This is best done before you begin a
training session. Check the lubrication as follows:
1. Ensure the treadmill is powered off! Step on the
treadmill belt .and stand steadily where you normally
run on the belt.
2. Take hold of the horizontal handlebar and push the
belt with your feet so that it slides back and forth. The
belt should move softly and evenly, without a sound.
3. If you notice jerky movement or if the belt will not
slide check for lubrication by sliding your hand under
the belt.
Lubricate the running deck according to the following
instructions:
A) FOLDING TREADMILL
1. Attach the nozzle of the lubrication tube to the T-
Lube S container.
2. Lift the running deck and lock it.
3. Position the nozzle between the belt and the board.
Try to reach the spray as far into the center of the
running deck as possible.
4. Spray the lubricant for 2-3 seconds.
5. Lower the running deck into its normal position.
Use treadmill for your training session. Or allow the
treadmill to run for at least 5 minutes.
B) NON-FOLDING TREADMILL
1. Attach the nozzle of the lubrication tube to the T-
Lube S container.
2. Adjust the running deck to its maximum elevation.
3. Position the nozzle between the belt and the board on
the underside of the treadmill. Try to reach the spray as
far into the center of the running deck as possible.
4. Spray the lubricant for 2-3 seconds.
5. Lower the running deck into its normal position. Use
your treadmill for your training session. Or allow the
treadmill to run for at least 5 minutes.
NOTE! Lubricate your treadmill only with T-Lube S
silicon lubricant. Contact your local Tunturi distributor
for further supplies of T-Lube or further information on
lubrication and maintenance.
ALIGNING THE RUNNING BELT
Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually needed,
provided
•
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
T60_manual_uusi versio_j.indd 11T60_manual_uusi versio_j.indd 11 25.10.2006 13:33:5525.10.2006 13:33:55