G B
7
O W NE R 'S MA N U AL • T 40
begin. Use the SPEED + / - keys to adjust the speed
and the INCLINE + / - keys to adjust the elevation. In
preset programs, you can change the resistance level
in the section of the profile you are performing at the
moment.
6. In the Program 7 to Program 9, the program
window will first display ”ENTER AGE”. Press + /
- button input your age and ENTER to confirm. The
program window will display “ENTER TARGET
HEART RATE”, press +/- button to input desired
target heart rate, then press ENTER to confirm the
target heart rate. The program window will display
“ENTER MAXIMUM SPEED”, press +/- button to
input desired max speed value, then press ENTER to
confirm the value. You can now enter the target time,
distance and calories. Press the START to
begin exercise. Heart rate controlled exercises
enable training at a selected heart rate level. Heart
rate controlled exercises always require heart rate
measurement.
USER 1 TO USER 3
1. Select the desired program with the + / - buttons.
The program window will display the profile.
2. Press ENTER to confirm your desired user setting
program.The program window will display “ENTER
YOUR WORKOUT TIME”. The TIME window
will glitter. Press + / - button to set up your to do the
exercise. Press ENTER to confirm your setting value.
3. The program window will display “ENTER YOUR
WORKOUT DISTANCE”. The DISTANCE window
will glitter, press + / - button to set up your desired
distance to do the exercise. Press ENTER to confirm
your setting value.
4. The program window will display “ ENTER
YOUR WORKOUT CALORIES”. The CALORIES
window will glitter, press + / - button to set up your
desired calories to do the exercise. Press ENTER to
confirm your setting value.
5. Press START to begin exercise.
EDITING THE PROFILE LEVELS
1. In the program window, the first column of LED
matrix will glitter. Press SPEED + / - to set up desired
speed value and press incline + / - to set up desired
incline level.
2. Press the enter button to confirm your profile
setting for first column.
3. Continue to finish all of the profile setting column
by column.
ENGINEERING MODE
1. During the power ON position, first hold the
SELECT button then press the ENTER button
together to enter the Engineering Mode
2. Elevation window shows software version – VER
and the model no. T40. distance window shows
software version, KCAL window shows year. Time
window shows Time, speed window shows diameter
of roller.
3. Press ENTER button window shows LDU version
and ISP version
4. Press ENTER button enter KM/MILE switch mode.
Press SPEED + - or ELEVATION + - to select KM or
MILE.
5. Press ENTER button window shows total distance.
6. Press ENTER button window shows total hour.
7. Press ENTER button goes back to ON position.
NOTE: press SELECT button for 5 seconds the speed
value will be clear off.
MAINTENANCE
The equipment is safe to use only when periodically
maintained and inspected for faults and wear.
CAUTION! Do not attempt any servicing or adjustment
other than those described in this manual. Any other
servicing must be performed by an authorized service
representative. Check the tightness of all fixing
screws once a year. Do not overtighten.
LUBRICATING THE RUNNING DECK
In average domestic use (a maximum of 60 minutes a
day), you should check the lubrication approximately
after every 300 hours of use. The console is equipped
with a counter for measuring total values, thus
allowing you to monitor your total training time on
the treadmill. If there is any jerky movement of the
belt, always check the lubrication level. To do this, let
the treadmill come to a complete stop, then simply lift
the running belt to feel the running deck; if the deck
feels dry and there is very little evidence of lubricant
on your hand, lubricate the running deck according to
the following instructions:
1. Attach the nozzle to the lubricant container.
2. Let the treadmill come to a complete stop, and then
lift the running belt.
3. Position nozzle between the belt and the board
approximately 200 mm (8”) from the front of the
treadmill.
4. Apply T-Lube from the front to the rear of the
treadmill on each side of the treadmill, spraying as
far into the center of the running base as possible.
One T-lube container will be sufficient for two re-
lubrications.
5. The treadmill is instantly ready for use.
NOTE! When lubricating the treadmill, you should let
it run at least five minutes before lifting the running
deck to the storage position. This will prevent the
lubricant from spilling.
NOTE! Lubricate your treadmill only with T-Lube
S silicon lubricant. Contact your local Tunturi
distributor for further supplies of T-Lube.
CLEANING THE TREADMILL
Wipe the treadmill surfaces, especially the handlebars
and meter from dust with a damp cloth or towel.
Do not use solvents. Use a small vacuum nozzle to
carefully vacuum around all visible components (belt,
running deck, side rails etc.). To clean the underside
of the treadmill, lift the running deck to the storage
position.