Filter
Top Products
11
MEMORY FUNCTION
The Memory function requires the use of a user code:
the exercise is saved under the selected user code. You
can save 5 exercises under each user code.
SAVING YOUR OWN PROFILE:
1. You can save preset proles once the exercise is
completed, or after nishing the exercise by pressing
STOP once. If you want to save your Manual or HRC
workouts, nish the exercise by pressing STOP once.
Save your exercise by pressing MEM.
2. The display prompts for a memory slot (SAVE AS
OWN 1-5). Select the desired memory slot with the
jogwheel and press JOGWHEEL to conrm your selection:
your workout is now saved to the desired slot.
3. If there are no empty memory slots, replace a previous
prole with a new one. The display then prompts you
to conrm (REPLACE OWN 1-5). Press JOGWHEEL to
conrm your selection: your workout is now saved to
the desired slot.
4. SAVED AS OWN 1-5 is displayed to conrm your
save. The console will automatically switch to its initial
state.
NOTE! To save a prole, you need to exercise for 10
minutes or more.
USING YOUR OWN PROFILE:
1. Select your user code.
2. Press MEM.
3. Use JOGWHEEL until the signal light indicates the desired
own prole (-1-5 MEMORY). Press JOGWHEEL to conrm
your selection. Select RERUN (to use the prole without
adjustments) or RACE (to use the prole as a basis for the
Race function) with the JOGWHEEL key.
4. Press JOGWHEEL to conrm your selection.
5. Press START to begin the prole.
6. The RERUN function allows you to scale your own prole
and save the changes.
RACE FUNCTION
To race against a previously saved exercise, select RACE
in the Own Prole menu.
1. Press START. The exercise begins and the belt starts
moving.
2. Adjust the speed according to your tness level either
manually or using the PSC function.
3. The console display shows information on prole
progress and any changes ahead.
4. Once the prole has been completed, the cool-down
period will automatically start. You can save your workout
in the console’s memory (see Memory Function).
MAINTENANCE
The equipment is safe to use only when periodically
maintained and inspected for faults and wear. Do not
attempt any servicing or adjustment other than those
described in this manual. Any other servicing must be
performed by an authorized service representative.
Check the tightness of all xing screws once a year.
Do not overtighten. Defective components must be
immediately replaced: the equipment must not be
operated with any defective components.
CLEANING AND LUbRICATING THE TREADMILL
FAILURE TO LUBRICATE YOUR TREADMILL MAY
INVALIDATE THE PRODUCT’S WARRANTY!
Wipe the treadmill surfaces, especially the handlebars
and console from dust with a damp cloth or towel.
Do not use solvents. Use a small vacuum nozzle to
carefully vacuum around all visible components (belt,
running deck, side rails etc.). Also keep the area near
the treadmill clean. While in use, the treadmill gathers
dust that may cause problems in the operation of the
equipment.
In average domestic use (a maximum of 60 minutes a
day), you should check the lubrication once a month
– however, lubricate the belt only if needed. In more
demanding use, the lubrication needs be checked at
shorter intervals. This is best done before you begin a
training session. Check the lubrication as follows:
1. Ensure the treadmill is powered off! Step on the
treadmill belt and stand steadily where you normally
run on the belt.
2. Take hold of the horizontal handlebar and push the
belt with your feet so that it slides back and forth. The
belt should move softly and evenly, without a sound.
3. If you notice jerky movement or if the belt will not
slide check for lubrication by sliding your hand under
the belt. Lubricate the running deck according to the
following instructions:
NOTE! Lubricate your treadmill only with T-Lube S
silicon lubricant. Contact your local Tunturi distributor
for further supplies of T-Lube or further information on
lubrication and maintenance.
IMPORTANT! Treadmills need constant lubrication.
After not using the machine for a while, the deck could
dry out and needs to be lubricated. Make sure you check
after long periods if the belt needs lubrication. To
lubricate open the small caps at the end of the treadmill
with a small coin. And squeeze half the bottle of T-lube.
The lubrication system will make sure the belt is evenly
lubricated.
T70 & T80 - OWNER’S MANUAL ENGLISH