Filter
Top Products
THIS CONCLUDES TIIE ASSEMBLY OF (ZEFEL
425101 HOME GYM ASSEMBLY PARTS LIST
COUNT ALL PARTS BEFORE BEGINNI!NG ASSEMBLY
HARDWARE:
ITEM .NAME/DESCRIPTION QTY
7.
$.
9.
I0.
11.
12.
13.
14.
¯ 318 X’3 IN..BOLT .........................
~ .....................................................
:. .........................~. ......................................
2
I/2 X 3-’I/2 IN~ ’BOLT ................................................................................................................... ~ ......................1
1/2 X 4 IN. BOLT ................................................................ ~: .................................". ......................~ ....., ..............1
318 IN. WASHER ......................................... ~...~. ...................................................................................................2
1/2 IN. WASHER .....................................................................
; ............................................................................4
3/8 IN. LOCK WASHER ..................................................................
2 ...................................................................2
1/2_ IN. LOCKNUT
" "
" ,
"
2
CONTROL LEVER
,1
3/4 IN. FLANGE BEARING
’
2
I/2 IN. FLANGE BEARING ................................................................................................ ................................
4
3/8 l’N. JOINT CONNECTOR CAP ............................................................
: ........................................................2
#8 INT. TOOTH LOCK WASHER ....................................................................................................................
: 2
8-32 X 3/16 IN. SCREW
’
2
E-KING ...........................................................................................................
5/16 X 3/8 IN. SET SCREW ................................................................................................................................
2
PARAGLIDE STRIP ............. ~ ................................, .............................................................................................
8
4 IN. VINYL SLEEVE .........................................................................................................................................
1
ADHESIVE CLIP ................................ ’ ...............
~ .................................................................................................
1
WELDMENTS/PARTS:
ITEM
NAME/DESCRIPTION QTY
I. PRESS ARM ...................................................................
(6538401) ...................................................
." ................
I
2. RECEIVING TUBE ........................................................
(6539201) .................................................................... 1
3. PRESS ADJUSTMENT TUBE .......................................
(6534602) ....................................................................
I
"4. I0-I/4 IN. AXLE ...............................................~ ......~ ......(62{]~-601);: ....................." .....................................
.’ .......
I
5.
PAD, IS-ira. X 10-1/2 ........
~ ............................
,: ...............
(6457301) .....................................................................
1
I.
Inse~t the PUSH/PULL CABLE through the bottom .oftheRRESS ARM up to the CONTROL LEV~-’R as shown in
.(DETAIL A), and hold in pla~e with one (1)E-RING.
2. SECURELY assemble the PUSH/PULL CABLE to the CONTROL LEVER as shown in (DETAIL A), using one (1)
IN. JOINT CONNECTOR CAP, one (I) #8 INT. TOOTH LOCK WASHER, and one (1) 8-32 X 3/16 IN. SCREW.
Slide one (I) IN. VI NYL SLEEVE over th e CONTROL LEVER. Then SECURELY assemble th e CONTROL LEVER to
the_TA.R.at~.tha/~ EfiSARM..~s~ho.wm_ia.(DETAIL_K)Ja~u~omwd,/l/iS_ lh[,JD[hEL~OBlq!CZD~’,..CKP.~n~..CD,.~-.I’ST ........
TOOTH LOCK WASHER, and one (I) 8-32 X 3/16 IN. SCREW.’
Attach four (4) PAPA.GLIDE STRIPS inside the end of the RECEIVING TUBE, and four (4) PAPA.GLIDE STRIPS
ou~ide the end of the PRESS ADJUSTMENT TUBE as shown in (DETAIL B), using the followin@ steps:
¯
Thoroughly clean all surfaces where the PARAGLIDE STRIPS are to be attached.
07P_2~6