Filter
Top Products
WHEELS DO NOT ROTATE FREELY AFTER THE BOLTS ARE TIGHT, REMOVE WASHERS.)
SECURELY assemble ~he SEAT PAD to the ADJUSTABLE PRESS SEAT as shown on/rzwing, using two (2) 3;8 X
314 IN. BOLTS, two (2) 318 IN. LOCK WASHERS, and two (2) 318 IN. WASHERS.
Pull back the SPRING PrN on the PRESS BACK SUPPORT and.slide the ADJUSTABLE PRESS SEAT into the
RECEIVING W’ELL. Engage the SPRING PIN into one of the adjustment holes. Secure the ADJUSTABLE PRESS SEAT
in place with one (1) THUMBSCREW.
SECURELY assemble the BACK PAD t6 the PRESS BACK SUPPORT as shown on drawing, using two (2) 3/8 X 3 IN.
BOLTS, two (2) 3/~ IN. LOCK WASHERS, and two (2) 3/8 IN. WASHERS.
Insert two (2) I/2 IN. FLANGE BEARINGS into the PRESS SUPPORT TUBE as shown on drawing.
"..SECURELY"assemble.the PRESSBACK SUPPDRT to the.PRESS suPPORT TU.BE,~s shown in drawing;using one (I)
I~.X3~I/’2 IN. :BOLT/:two" (2) I/2IN.~W.ASHERS,.~m~d one (I)I/2 IN~.LOCK NUT. (~IGHTEN THE CONNECTION
ENOUGH TO.REMOVE’THE :PLAY,~/ET.ALLOWING THEPRESS BACK SUPPORT..TO ]ROTATE FREELY)
SECURELY assemble one (I) ID_ I~ SPRING PIN.ASSEMBLY to the SPRING PIN HOUSING, of the PRESS
SUPPORT TUBE Rs shown in (DETAIL E). (!!! IMPORTANT !!! TIGHTEN THE NUT Oi~ .THE SPRING
ASSEMBLY SECUILI’. LY) "~ ...................... -’
SECURELY assemble, the BEARING HOUSING and the CENTER PULLEY BRACKET to the ]FRONT UPRIGHT ~s
shown.on drawing, using two(2) 1/2 X 3-1/2IN. BOLTS, four (4) I/2 IN. WASHERS, and two (2) 1/2 IN. LOCK
(THE CONNECTOR PLATES ON THE BEARING HOUSING AND THE CENTER PULLEY BRACKET HAVE
SLOTTED HOLES. SHIFT THE BEARING HOUSING DOWN AND THE CENTER PULLEY BRACKET UP AS
FAR AS POSSIBLE)
o
¯
Assemble two (2) 3/4 IN. THRUST WASHERS and two (2) PEC CAMS to the LEFT and RIGHT :FEC ARMS, as shown
¯
on drawing.
Insert four (4) .3/4 IN. FLANGE BEARINGS into the BUSHINGS of the BEARING HOUSING, as shown on drawing.
ll. Insert the LEFT and RIGHT PEC DEC ARMS through the 3/4 IN. FLANGE BEARINGS in the BEARING HOUSING
on their respective sides as shown on drawing, and SECURE ~hem in place with two (2) 3/4 I.D. STAR LOCK COLLARS.
12.
¯
..Attach two (2) 1 X 1 IN. CARKIAGE GUIDES to the ANGLE on the BEARING HOUSING where the PEC CAMS
,make contact with the ANGLE.
.Slide t~,.o (2) 4 X 12 ROLLER PADS onto the LEFT and RIGHT PE’C.D~.C ’ARMS, umirthe ROLLER PAD is FLUSH
,~ith the bottom of.the ARMS. (IF A LUBRICANT-IS REQUIRED, COAT THE INSIDE OF THE ROLLER PAD
"WITH RUBBING ALCOHOL ALSO, ROTATING THE PAD WHILEP.USHING UP WILL HELP TO EASE
’ASSEMBLY)
14. SECURELY assemble two (2) 3/8 IN. SPRING PIN ASSEMBLIES to the SPRING PIN BARRELS, ofthe PEC CAMS
sho,h’n in (DETAIL B). (!!! IMPORTANT !!! TIGHTEN THE NUTOF THE SPRING PIN ASSEMBLY SECURELY)
15.
PULLEY BRACKET as shown in (DETAIL D), using two (2) 3/8 X 2 IN. BOLTS, two (2) 3/$ IN. WASHERS, and
(2) 3/8 IN~ LOCK NUTS. (NOTE: THIS CONNECTION WILL BE TIGHTENED AFTER THE CABLE HAS BEEN
ROUTED)
.... place with three (.3) I/4.IN. CAP NUTS.
THIS CONCLUDES THE ASSEMBLY OF (LEVEL
425101 HOME GYM ASSEMBLY PARTS LIST .(LEVEL’6)
LOOSELY’asscmble.two (2) 3-I~ X 1 IN..P.ULLEYS and two (2) 2-3/,~ IN, CABLE RETAINING CLIPS to the CENTER
II
07~6