~:’ ROLLE~. PAD SHAFT ..............................
i ....................(6435301) ....................................................................
l
-5..
ROLLER PAD .................................................................
(6194601) ....................................................................
2
~. 3-l/2 X ! iN. PULLEY ....................................................
(3116201) .....................................................................
!
?. .......
4-I~ X I IN. PULLEY ...................................................
(311610~) ...... ..............................................................
1
LOOSELY assemble the FRONT and MIDDLE UPRIGHTS to the BASE as shown on drawing, using four (4) 31g X 2 IN.
BOLTS¯ eight (8) 3/8 IN. WASHERS, and four (4) 3/8 IN. LOCK NUTS.
LOOSELY assembl~ the REAR UPRIGHT to the BASE as shown on drawing, using two (2) I~ 3.1/4 IN. BOLTS, four
(4) l~ I"N. WASHER.S, and two (2) I/2. IN. LOCK NUTS.
LOOSELY assemble th~ PRESS BASE to the REAR AND MIDDLE’UPRIGHTS, using four (4) ~/g X 3 IN. BOL’I~,
.eight (g) 3/8 IN. WASHEP,.S, and four .(4) 3/g IN. LOCK NUTS.
i~OOSELY.assemblethePRESS :BASE:tothe BASE as shown on drawing, using two (2) IP- X 3-I/4 IN..BOLTS¯ four (4)
I/2. rN. WASHERS, and two (2) l~ IN. LOCK NUTS.
SECURELY assemble one (I) 3-I/2 X 1 IN. PULLEY to the FRONT UPRIGHT as shown on drawing, using one (I)
X 2-314 IN. BOLT, two (2) 31g IN. FLANGE SPACERS, and one (I) 31.g IN. LOCK NUT, .........
SECURELY assemble one (I) 31g X 2-3/4 IN. BOLT, two (2) 318 IN. WASHERS, and one (I) 318 IN.. LOCK NUT
FRONT UPRIGHT in the hole above the pullsy assembled in STEP 4.
.SECURELY assemble one (I) 318 IN. SPRING PIN ASSEMBLY to the SPRING PIN HOUSING, of’the FRONT
UPRIGHT as shown in (DETAIL A). (Ill IMPORTANT !!! TIGHTEN THE NUT OF THE SPR]ING
ASSEMBLY SECURELY)
o
10.
A~tach one (I) THUMBSCREW to the FRONT UPRIGHT as.shown on drawing.
Assemble two (2) ROLLER PADS to the FRONT UPRIGHT as shown on drawing, using one (I) ROLLER
SHAFT, and two (2) 9/I 6 M’USHROOM CAPS.
SECURELY assemble one (I) 4-I/2 X I IN. PULLEY to the HORIZONTAL FLAT o’f the PRESS BASE using one (1)
.~/$ X 2 IN. BOLT, one (I) 2-7/8 IN. CABLE RETAINING CLIP, one (1) 3/8 IN. WASHER, and one (1) .3/~ IN.
NUT.
THIS CONCLUDES THE ASSElVIBLY OF (LEVEL 2)
425101 HOME GYM ASSEMBLY PARTS LIST (LEVEL
COL".’NT ALL PARTS BEFORE BEGIN’NING ASSEMBLY
.H,~RDWARE:
ITEM
NAME/DESCRIPTION
QTY"
~/8 X l-1/2 IN. BOLT ...........................................................................................................................................I.
2.
.~/~ X 2-I/4 IN. BOLT ...........................................
’ .................................................................................................
.% .~/I~ X 2-2/4 IN. BOLT .............................................................................................................................................
~. 3/~ X 3 IN. BOLT
... ....................................................6
~. T~ ~’X’~"-~.’BOLT, ...................................................................................................................................................
( I~ X 3-114 BOLT ...................................................................................................................................................
1
6~, ’
314 IN. WASHER ....................................................................................................................................................
7. I/2 IN. WASHER ....................................................................................................................................................
5
8. 3/~ IN. WASHER
"
9.
3/8 IN. LOCK WAS~ER
