Filter
Top Products
_1 Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
B Select one of the personal trainer programs.
When the key
is inserted, the
manual mode
willbe se-
lected. To se-
lect one of the
personal
trainer programs, press the Program button re-
peatedly until one of the six personal trainer pro-
gram indicators lights. When a personal trainer
program is selected, theTime/Incline/Segment
Time display will flash the maximum incline setting
forthe program, and the Speed/Min-mile display
willflash the maximum speed setting, for six sec-
onds.
The six profiles on the right side of the console
show how the speed and inclineof the treadmill
will change during the programs. The numbers
beside the profiles show the maximum speed and
incline settings for the programs.
The program display
will show the first
speed settings for the
program. The Time/
Incline/Segment Time
display will show how
long the program will
last.
mJ_r_ome_.
0000000
00000@@
0000@@@
000®@0@
00@@@@@
_1 Press the Start button or the Speed A button to
start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. The Time/Incline/
Segment Time display will show both the time re-
maining in the program and the time remaining in
the current segment. One speed setting and one
incline setting are programmed for each segment.
(The same speed setting and/or incline setting may
be programmed for consecutive segments.) The
speed setting for the Current Segment
first segment will be
shown in the flashing
Current Segment col-
umn of the program dis-
play. (The incline set-
tings are not shown in
the program display.)
The speed settings for the next four segments will
be shown in the four columns to the dght.
oo( o o-o-_
OOCO0@@
00(0@@@
00(@@@@
ooceoe_
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the rightwill flash and a
tone will sound. In addition, if the speed and/or
incline of the treadmill isabout to change, the
Speed/Min-mile display and/or the Time/Incline/
Segment Time display will flash to alert you, and
three tones will sound. When the first segment is
completed, all speed settings will move one col-
umn to the left. The speed setting for the second
segment will then be shown in the flashing
Current Segment column and the treadmill will au-
tomatically adjust to the speed and inclinesettings
for the second segment.
The program will continue in this way untilthe
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the Time/Incline/Segment Time display. The walk-
ing belt Willthen slow to a stop.
Note: Each time a segment ends and the speed
settings moveone column to the left, flail of the
indicatorsin the Current Segment column are lit,
the speed settings will move downward so that onty
the highest indicators in the columns will appear in
the program display. When the speed settings
move to the left again and not all of the indicators
in the Current Segment column are lit, the speed
settings will move back up.
If the speed or incline setting for the current
segment istoo high or too low,you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times one of the Speed
buttons is pressed, an additional indicator will light
or darken in the Current Segment column. If any of
the columns to the dght of the Current Segment
column have the same number of lit indicators as
the Current Segment column, an additional indica-
tor may light or darken in those columns as wel!.
Important: When the current segment of the
program ends, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
12