Filter
Top Products
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 21.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD
PLAYER, VCR, OR COMPUTER on page
20.
Note: To purchase iFIT.com CDs and videocas-
settes, visit our Web site at www.iconeurope.com.
Follow the steps below to use an iFIT.com CD or video
program.
Insert the key fully into the console.
See GETTING STARTED on page 11.
Select the iFIT.com mode.
When the key is in-
serted, the manual
mode will be selected.
To use an iFIT.com CD
or video program, press
the iFIT.com button. The
indicator above the button will light and the words
“IFIT MODE” will appear in the main display.
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the PLAY button on your CD player or
VCR.
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the time is flashing in the
main display, press the Start button or the Speed
+ button on the console. The treadmill will not re-
spond to a CD or video program whilst the time is
flashing.
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed
and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
4
3
2
1
1522
B
A
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
ANT
. IN
RF OUT
IN
OUT
CH
3
4
C
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
ANT. IN
RF OUT
IN
OUT
CH
3
4
Audio
Cable
Adapter
A
B
A
AUDIO OUT
RIGHT
LEFT
VIDEO
AUDIO
ANT. IN
RF OUT
IN
OUT
CH
34
C
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
ANT. IN
RF OUT
IN
OUT
CH
34
Audio
Cable
Adapter
B
Wire removed from
AUDIO OUT jack
RCA
Y-adapter
If the speed or incline setting is too high or too low
during the program, you can manually override
the setting by pressing the Speed or Incline but
-
tons on the console. Every few times one of the
Speed buttons is pressed, an additional
indicator
will light or darken in the Current Segment column.
(If any of the columns to the right of the Current
Segment column have the same number of lit indi-
cators as the Current Segment column, an addi-
tional indicator may light or darken in those
columns as well.) Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
in the program display will not move downward as
described above. Note: If you manually override
the speed or incline setting, when the next seg-
ment begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
To stop the program temporarily, press the Stop
button. The time will begin to
flash in the main dis-
play. To restart the program, press the Start button
or the Speed + button. The walking belt will begin
to move at 1 mph. When the next segment begins,
the treadmill will automatically adjust to the speed
and incline settings for the next segment. To end
the program, press the Stop button, remove the
key, and then reinsert the key.
Follow your progress with the displays.
See step 5 on page 12.
Measure your heart rate if desired.
See step 6 on page 13.
Turn on the fans if desired.
See step 7 on page 13.
When the program has ended, remove the key.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at the lowest level. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays and indicators
on the console remain lit after the key is re
-
moved, the console is in the “demo” mode.
See page 25 and turn off the demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off po-
sition and unplug the power cord.
7
6
5
4
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS