Functional overview (cont’d)
Before you start
Using a remote control
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor of the
unit.
• Remote operation may become unreliable if
strong sunlight or fluorescent light is on the
remote sensor of the unit.
• Remote control for different devices can inter-
fere with each other. Avoid using remote control
for other equipment located close to the unit.
• Replace the batteries when you notice a fall-off
of the operating range of the remote control.
• The maximum operable ranges from the unit are
as follows.
- Beeline: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m) within 15°
- Below: approx. 10 feet (3m) within 30°
Installing batteries in the remote control
Install two “AA” size batteries (supplied), matching
their polarity to those indicated inside battery com-
partment of the remote control.
Note:
Incorrect use of batteries can result in hazards such
as leakage and bursting. Please follow the instruction
below:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
Although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of each
battery match the indications in the battery com-
partment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing used batteries, please comply with
governmental regulations or public rules for envi-
ronmental protection that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or disas-
semble batteries.
10
Because this product is a combination of a VCR and a DVD recorder, you must select first which com-
ponent you wish to operate with [SELECT].
Hit [VCR] on the remote control.
(Verify that the VCR indicator is lit.)
VCR MODE
Hit [DVD] on the remote control.
(Verify that the DVD indicator is lit.)
DVD MODE
The VCR/DVD recorder Switching
Notes:
• Hitting only [SELECT] on the front panel
DOES NOT switch the mode of the remote
control.You MUST select the correct mode on
the remote control.
• You cannot switch to another mode (DVD or
VCR) during in the timer-standby mode.
• Pressing [REC/OTR] (DVD) or [REC/OTR]
(VCR) on the remote control switches immedi-
ately its respective mode so that you can start
recording directly on the appropriate media.
R
E
P
E
A
T
T
R
K
.
D
V
D
V
I
D
E
O
S
-
V
I
D
E
O
L
-
A
U
D
I
O
-
R
P
O
W
E
R
R
EW
F
.
F
W
D
P
L
A
Y
R
E
C
O
R
D
S
T
O
P
/
E
J
E
C
T
D
U
B
B
I
N
G
O
P
E
N
/C
L
O
S
E
V
C
R
S
E
L
E
C
T
S
E
L
E
C
T
D
V
D
S
T
O
P
P
L
A
Y
C
H
A
N
N
E
L
R
E
C
O
R
D
S
K
I
P
R
E
C
P
A
U
S
E
P
E
N
T
E
R
M
E
N
U
P
L
A
Y
L
I
S
T
TO
P
M
E
NU
/
O
R
IG
IN
A
L
k
K
F
W
D
g
ST
OP
C
P
LA
Y
B
REV
h
HG
Remote
control
Within about
23feet (7m)
30˚
30˚
STOP
POWER
T-SET
TIMER PROG.
SKIP SKIP
OPEN/CLOSE
SPACE
123
456
78
0
9
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
DISPLAY
TUV WXYZ
DVD
REC/OTR
REC SPEED
ZOOM
SEARCH
VCR
SETUP
CM SKIP
RETURN
MENU/LIST
TOP MENU
DUBBING
REC MONITOR
CLEAR
ENTER
PLAY
AUDIO
DVD button
VCR button
VIDEOS
-
VIDEO
L
-
AUDIO
-
R
POWER
REW F.FWD PLAYRECORD
STOP/EJECT
DUBBING
OPEN/CLOSE
VCR
SELECT
SELECT
DVD
STOP PLAYCHANNEL RECORD
VCR
SELECT
DVD
SELECT button
DVD indicator
VCR indicator
E9600UD_EN/SP.qx3 05.4.25 15:16 Page 10
