Filter
Top Products
GB
O W N ER ’ S M AN U AL
5
POWER CORD
Plug the socket end of the transformer cord into the
connector, just above the rear support in the centre of
the frame, and the other end into the wall socket. To
prevent damage to the connector, we recommend you
tie the cord to the transportation wheel support next to
the connector.
NOTE!
The device must be connected
to a grounded wall socket.
Do not use extension wires
when connecting the device to
the power source. Make sure
the power cord does not run
underneath the device.
Always switch off the power
and uplug this appliance from
the electrical outlet immediately
after using.
ADJUSTMENTS
Set the right height for you; the basic rule is that the
arch of the foot reaches reaches the the pedal at its
lowest point with the leg almost straight. Adjust the
seat height by loosening the seat locking knob. Hold on
to the seat with one hand and, using your other hand,
pull the locking knob outwards in order to enable free
seat tube movement upwards and downwards. Once the
height is right, let go of the knob and the seat locks into
place. Turn the locking knob clockwise to tighten.
NOTE! Always make sure that the locking knob is
properly fastened before starting to exercise!
To adjust the horizontal seat position forward and back,
loosen the locking screws under the seat. You can also
adjust inclination from here. Release the seat lock by
turning the locking lever located under the seat anti-
clockwise. Adjust the seat to the desired position and
tighten the locking lever by turning it clockwise.
HANDLEBAR SETUP
Loosen the locking screw on the front of the handlebar
support and find the right angle at which to position
the handlebar. Tighten the locking screw. The design of
the handlebar allows you to exercise either in an upright
position or with the upper body leaning forward.
Remember, however, always to keep your back straight.
Adjust the handlebar height by loosening the locking
knob on the handlebar support tube. Pull the locking
knob outwards so that the handlebar can be moved
freely up and down. Release the knob once the
handlebar is at the required height. The handlebar
support tube will click into place. Tighten the locking
knob by turning it clockwise.
CONSOLE INCLINATION ADJUSTMENT
Set the inclination of the meter so that it corresponds to
your height and exercise position.
ADJUSTMENT OF SUPPORT FEET
If the equipment is not stable, adjust the adjustment
screws below the support feet as necessary.
EXERCISING
Working out with this device is excellent aerobic
exercise, the principle being that the exercise should be
suitably light, but of long duration. Aerobic exercise
is based on improving the body’s maximum oxygen
uptake, which in turn improves endurance and fitness.
The ability of the body to burn fat as a fuel is directly
dependent on its oxygen-uptake capacity. Aerobic
exercise should be above all pleasant. You should work
up a light sweat but you should not get out of breath
during the workout.
You should exercise at least three times a week, 30
minutes at a time, to reach a basic fitness level.
Maintaining this level requires a few exercise sessions
each week. Once the basic condition has been reached,
it is easily improved, simply by increasing the number
of exercise sessions. You should start slowly at a low
pedaling speed and low resistance, because for an
overweight person strenuous exercise may subject the
heart and circulatory system to excessive strain. As
fitness improves, resistance and pedaling speed can be
increased gradually.
HEART RATE
No matter what your goal, you’ll get the best results by
training at the right level of effort, and the best measure
is your own heart rate.
HEART RATE MEASUREMENT WITH HANDGRIP
SENSORS
Heart rate is measured from the hands using the sensors
located on the handlebars. The sensors measure electric
impulses, which are formed when a person’s heart beats.
Measurement is started by touching both handlebar
sensors simultaneously. To ensure reliable heart rate
measurement, skin must be slightly moist and skin
contact with sensors must be continuous. If skin is too
dry or too wet, the heart rate measurement operation
from the hands is less reliable. Try to keep your upper
body and palms relaxed and still.