Star Trac UB Sport Upright Bike Elliptical Trainer User Manual


  Open as PDF
of 36
 
26 STAR TRAC SPORT BIKES OWNER’S MANUAL
9. If desired, you can use the personal fan during your workout (see “Using the Personal Fan” for details).
10. If you wish to pause the program, stop pedaling. The bike enters pause mode and a “P” flashes in the T
IME Window.
Resume pedaling within 25 seconds to continue your workout.
11. When you have reached your workout goal, the bike enters the Cooldown cycle (see “Cooldown Cycle” for details). If you
wish to exit the program before you have reached your workout goal, stop pedaling and allow the Pause timer to expire.
BURN FAT PROGRAM
The BURN FAT program is similar to the CONSTANT HEART RATE program. It is designed to maintain your heart rate at a constant
level equal to 62.55% of your theoretical maximum heart rate (220 BPM – age) by controlling pedaling resistance and prompting
you to pedal at a specified RPM. Please note that your heart rate may vary above and below the target heart rate during this
program.
To operate the B
URN FAT Control program:
1. Mount the bike (please refer to “Seat Adjustments” section) and begin pedaling.
■ If necessary, enter the Lockout ID to enable the bike for operation (see “Lockout ID Processing” for details).
2. Press the
key.
3. You are prompted to select the desired A
DVANCED WORKOUTS program. Press the key to select the HEART RATE
TRAINING programs, then press the key when prompted to select the BURN FAT program.
4. You are prompted to enter your weight. The bike displays a default weight of 155 pounds (70 kg). You may enter any
weight from 0 to 500 pounds (0 to 226 kg).
■ Use the
keys to enter your current weight; or press the or key, as necessary, to increase or decrease
the displayed weight in 1 pound (or 1 kg) increments.
■ When your correct weight has been entered, press the key to accept the displayed value.
5. You are prompted to enter a time goal. The bike displays a default time of 99 minutes. You may enter any time from 1 to
99 minutes.
■ Use the
keys to enter your desired time goal; or press the or key, as necessary, to increase or
decrease the displayed value in 1 minute increments.
■ When your desired goal has been entered, press the key to accept the displayed value.
6. You are prompted to enter your age.
■ Use the keys to enter your age, or press the or key, as necessary, to increase or decrease the
displayed value in 1 year increments.
■ When your correct age has been entered, press the
key to accept the displayed value.
7. If desired, you can use the personal fan during your workout (see “Using the Personal Fan” for details).
8. If you wish to pause the program, stop pedaling. The bike enters pause mode and a “P” flashes in the TIME Window.
Resume pedaling within 25 seconds to continue your workout.
9. When you have reached your workout goal, the bike enters the Cooldown cycle (see “Cooldown Cycle” for details). If you
wish to exit the program before you have reached your workout goal, stop pedaling and allow the Pause timer to expire.
FITNESS TEST
The FITNESS TEST performs a single-stage, sub-maximal protocol, and calculates the results using the Astrand-Rhyming
nomogram. The FITNESS TEST requires 6~7 minutes to complete. During the FITNESS TEST, you will be required to pedal at a
constant 60 revolutions per minute (RPM). You can view your RPM’s in the RPM window on the Display Panel.
NOTE: The test information is invalid if the RPM is not maintained at approximately 60 RPM.
You are required to raise your heart rate between 120 and 170 BPM for minutes 5, 6 and 7 (optional minute determined by the
program). If, during the test, your heart rate reading levels out increase the resistance L
EVEL, but DO NOT change the speed at
which you are pedaling.
STAR TRAC SPORT BIKES OWNER’S MANUAL 11
ASSEMBLY AND SETUP
SPORT UPRIGHT BIKE ASSEMBLY
AND SETUP
Use the following procedures to unpack and assemble your STAR TRAC
UB / Ubx SPORT UPRIGHT BIKE.
UNPACKING
Open the shipping carton, remove all parts from the carton and foam
inserts, and verify that the following parts are included in your shipment:
Description Qty
Bike Frame 1
Display Console Assembly 1
Seat Post Assembly 1
Front Foot 1
Rear Foot 1
Pedals (set of two) 1
Screw, Button Head, M10 X 30 8
Screw, Flat Head, M6 X 16 4
Screw, Socket Head, M6 X 10 1
TOOLS REQUIRED
Most STAR TRAC bikes can be assembled using the following tools:
■
Metric Hex Key Wrenches
■
Metric Open-End Wrenches
■
Metric Ratchet Socket Wrench Set
■
Torque Wrench
■
Channel Lock Pliers
■
Vice Grip Pliers
■
Rubber Mallet
■
Phillips Head Screwdriver
Your STAR TRAC UB / Ubx SPORT UPRIGHT BIKE includes a hex key set and combination open-end wrench.
ASSEMBLY
1. Install the Front Foot
NOTE: The front foot assembly has wheels attached to the front
edge. Be sure the wheels face forward when installing the front foot
assembly.
Stand the bike frame upright and place the front foot assembly
under the frame, aligning the holes in the foot with the holes in
the frame.
NOTE: It may be necessary to raise the frame slightly to align the
holes in the frame with the mating holes in the front foot.
Using four M10 X 30 button head screws, secure the front foot
assembly to the frame. Tighten all four screws securely.
Step 1
 previous next