Filter
Top Products
093
o
I1.
- 12.
13.
14.
15.
16.
BODYSMITi-I PROSYSTEM ASSEMBLY INSTRUCTIONS
Attach one (I) 1-1/4 SQ. RUBBER BUMPER to the CENTER of the CARRIAGE STOP on the
WEIGHT CARRIAGE.
Slide WEIGHT CARRIAGE down over the REAR UPRIGHT of the MAIN UPRIC-;HT. (NOTE:
MAKE SURE THAT THE WEIGHT PEG ON THE WEIGHT CAP,.RIAGE IS FACING
TOWARDS TFIE FRONT OF THE MACHINE)
LOOSELY attach the two (2) PULLEY MOUNT FLATS to the REAR and FROthT UPRIGHTS of the
MAIN UPRIGHT, using two (2) 3//I X 3 IN. BOLTS, two (2) 3/8 .IN. LOCK WASHERS, and two
IN. NUTS. (NOTE: THE HOLE CLOSEST TO THE END ON THE PULLEY MOUNT FLATS
SHOULD BE ASSEMBLED TO THE REAR UPRIGHT) (SEE DRAWING)
AT THIS TIME TIGHTEN ALL LOOSE FRAME CONNECTIONS MADE TO THIS POI_N~.
LOOSELY attach two (2) 3-1/20.D. X 1 IN. BUSHING PULLEY and four (4) ID_ IN. LG. PULLEY
SPACERS (ONE ON EACH SIDE OF THE PULLEYS) ber, veen the PULLEY MOUNT FLATS
above the WEIGHT-CARRIAGE, using two (2) 3/8 X 3 IN BOLTS, two (2) 3/g IN. LOCK WASI-~RS,
and two (2) 3/8 IN. NUTS.
Slide the two (2) ROD END COVERS over the ends of the LAT BAR HOLDER.
Slide the LAT BAR HOLDER over the PULLEY MOUNT FLATS, and LOOSELY assemble in place,
using one (1) 3/8 X 3-1/4 BOLT, and one (I) 3/g IN. HEIGHT LOCKNUT. (NOTE: USE ~
SECOND SET OF HOLES IN FROM THE END) (SEE DRAWING)
LOOSELY assemble one (1) 3-1/20.D. X 1 IN. BUSHING PULLEY, and two (2) lg.~ IN. LG. PULLEY
SPACER (ONE ON EACH SIDE .OF THE PULLEY) between the PULLEY MOUNT FLATS at the
FRONT, using one (I) 3/8 X 3-I/4 IN. BOLTS, one (1) 3/8 IN. LOCK WASHER, and one (1) 318
NUT.
LOOSELY resemble one (I) 4-I/20.D. X 1 IN. BUSHING PULLEY to the PULLEY BRACKET on the
UPRIGHT BRACE oft.he MAIN UPRIGHT, using one (1) .3/8 X 1-3/4 IN. BOLT, one (1) 3/g
LOCK WASHER, and one (1) 3/8 IN. NUT.
LOOSELY assemble one (1) 3-1/’20.D. X I IN. BUSHING PULLEY to the LOW ROW PULLEY
HOUSING of the MAIN UPRIGHT, using one (1) 3/8 X !-3/4 IN. BOLT, one(1) 3/g IN.
WASHER, and one (1) 3/8 IN. NUT.
To assemble the PULLEY BLOCK SYSTEM, SECURELY assemble two (2) PAINTED
CONNECTORS around two (2) 3-1/20.D. X 1 IN. BUSHING PULLEYS, using two> (2) 3/11 X2
BOLTS, four (4) 3/~I IN. WASHERS, and two (2) 3/8 IN. LOW HEIGHT LOCK NLU2S. (NOTE:
HOLES IN THE PAINTED CONNECTOR ARE OVAL, MAKE SUITE THAT THE PULLEYS AP~
AT THE IVlJ~J~IMUM WIDTH, SEE DETAIL G)