Remote control features
126 En
You can program remote control codes from other remote controls.
Use the learning feature if you want to program functions not
included in the basic operations covered by the remote control
codes, or an appropriate remote control code is not available. You
can program the function of other remote control to the buttons in
the highlighted areas in the following illustration. The buttons can
be programmed independently for each control area.
• The remote control transmits infrared rays. If the other remote control also
uses infrared rays, this remote control can learn most of its functions.
However, you may not be able to program some special signals or
extremely long transmissions. Refer to the operating instructions for the
other remote control.
• You cannot program the desired remote control code even if you select the
buttons in the highlighted area in the above illustration depending on the
selected control area and the assigned library.
1 Set the operation mode selector to FSOURCE and
then press an input selector button (3) to select the
desired control area.
The name of the control area you want to customize appears in
the display window (4) on the remote control.
y
• You can also select the desired control area by pressing 5SELECT
l / h repeatedly.
• If you want to select “TV”, set the operation mode selector to FTV.
Make sure that the operation mode selector is set to
F
SOURCE or
FTV. When you set the operation mode selector to FAMP and
program a remote control codes from other remote controls, the
programmed key cannot operate the amplifier function of this unit.
2 Press GSETUP using a ballpoint pen or similar
object.
“SETUP” appears in the display window (4).
3 Press 9k / n repeatedly to select “LEARN” and then
press 9ENTER.
The remote control enters the learning mode. “LEARN” and
the name of the selected control area appears in the display
window (4) alternately.
4 Place this remote control about 5 to 10 cm (2 to 4 in)
apart from the other remote control on a flat surface
so that their infrared transmitters are aimed at each
other and then press 9ENTER.
“L–KEY” appears in the display window (4).
5 Press the button for which you want to program the
new function.
“START” appears in the display window (4).
Programming codes from other remote
controls (LEARN)
Notes
Note
AMP
TV
SOURCE
ZONEMODE
SELECT
SETUP ID
MACRO
4
3
SYSTEM MEMORY
VOLUME
DVD CD
V-A UXMULTI
AVTV
PHONO
CD-R
POWER
STANDBY
POWERPOWER
DTV DVR VCR
DOCK
TUNER
XM
BD
HD DVD
MD
TAP E
CBL
SAT
NET
USB
REC
SRCH MODELEVEL
BAND
MENUTITLE
CLASSICAL 1 CLASSICAL 2 LIVE/CLUB ENTERTAIN
MEMORY
PC/MCX
RETURN DISPLAY
PRESET/CH
ENTER
CAT.
A-E
MUTE
2
1
NET RADIO
PRG SELECT
USB
MOVIE STEREO SUR. DECODE
EXTD SUR.
ENHANCER
THX STRAIGHT PURE DIRECT
PARTY SLEEP HDMI OUT AUDIO SEL
TV VOL TV CH TV
3D DSP
1234
5678
ENT.
MUTE AUDIO
INPUT
90
10
Set to
SOURCE
(U.S.A. and Canada models)
DVD
SETUP
START DVD
AMP
TV
SOURCE
ZONEMODE
SELECT
SETUP ID
MACRO
4
3
SYSTEM MEMORY
VOLUME
DVD CD
V-A UXMULTI
AVTV
PHONO
CD-R
POWER
STANDBY
POWERPOWER
DTV DVR VCR
DOCK
TUNER
XM
BD
HD DVD
MD
TAP E
CBL
SAT
NET
USB
SRCH MODE
LEVEL
BAND
MENU
TITLE
MEMORY
RETURN
DISPLAY
PRESET/CH
ENTER
CAT.
A-E
2
1
5 to 10 cm (2 to 4 in)
Other remote control
L-KEY
(U.S.A. and Canada
models)
AMP
TV
SOURCE
ZONEMODE
SELECT
SETUP ID
MACRO
4
3
SYSTEM MEMORY
VOLUME
DVD CD
V-A UXMULTI
AVTV
PHONO
CD-R
POWER
STANDBY
POWERPOWER
DTV DVR VCR
DOCK
TUNER
XM
BD
HD DVD
MD
TAP E
CBL
SAT
NET
USB
SRCH MODE
LEVEL
BAND
MENU
TITLE
MEMORY
RETURN
DISPLAY
PRESET/CH
ENTER
CAT.
A-E
2
1
START
(U.S.A. and Canada
models)
