))%()
&%-(R#+"-((
!-()*(*$(
Install per the Instructions shipped with the Kit.
!&+)&+""!*$!
%%*#&*(%"#&$%"
The push-pull kit provides direct connection of a
Cobra Gold or Prince XL torch to the
Power Feed™ 10M
Dual Wire Feeder
wire feeder.
The kit is intended for use with the following Cobra
Max, Python or Prince XL torches:
Cobra Max
K2252-1 Air Cooled 15ft.(4.5m)
K2252-2 Air Cooled 25ft.(7.6m)
Python
K2212-1 Water Cooled 15ft.(4.5m)
K2211-2 Air Cooled 25ft.(7.6m) K2212-2 Water Cooled 25ft.(7.6m)
K2211-3 Air Cooled 50ft.(15.6m) K2212-3 Water Cooled 50ft.(15m)
Prince XL
K1592-1 Water Cooled 15ft.(4.5)
K2296-2 Air Cooled 25ft.(7.6) K1592-2 Water Cooled 25ft.(7.6)
K1592-3 Water Cooled 50ft.(15.6
)
(8@BI84??<ACHGCBJ8EGBG;8&BJ8E887R#
H4?-<E88878E589BE8<AFG4??<A:G;8BAA86G<BA
74CG8E!<G
------------------------------------------------------------------------
(898EGBG;8%JA8EZF#4AH4?B9G;8*BE6;9BE
@C8E4:84A7HGLL6?8E4G<A:<A9BE@4G<BA*;8
GBE6;E4G<A:@4LABG@4G6;G;8E4G<A:B9G;8CBJ8E
FBHE68
------------------------------------------------------------------------
#!$-"-**&($."
%(%(%"*%($)*""
• Set the idle roll pressure on the wire drive between
an indicator reading of 0-2. A recommended start
point is 1.5.
• Depending on the weld mode, set the Voltage or
Trim at the
Power Feed™ 10M Dual Wire Feeder
using
the right control knob located on the upper case front
panel.
• The Wire Feed Speed (WFS) is set using the control
knob on the Torch. The left control knob on the
Power
Feed™ 10M Dual Wire Feeder
is inactive. The actual
WFS being set at the torch is displayed on the
Power
Feed™ 10M Dual Wire Feeder
.
• All weld parameters normally available for the active
weld mode are available during push-pull operation.
Refer to the Operation Section of this manual.
!)+((+"*%(
Adjustable flow regulator with removable adjuster key for
CO2 and Argon blend gases. Mounts onto feeder inlet,
and reduces gas waste and arc start “blow” by reducing
surge caused by excess pressure in supply hose.
Install the 5/8-18 male outlet of the regulator to the 5/8-
18 female gas inlet on the back panel of the wire drive.
Secure fitting with flow adjuster key at top. Attach gas
supply to 5/8-18 female inlet of regulator per INSTALLA-
TION section.
!"*+*/)*(!*
This option provides 4 casters and all required hardware
to mount it to the Power Feed Wire Feeder.
!$)+"*"*%%!
For applications where an insulated lift hook is required.
This kit provides an easily installed, heavy duty insulated
lift eye that mounts to the wire reel stand mast. See the
instructions provided with the kit for installation.
!%$+*&*(
Install per the Instructions shipped with the Kit.
!$%#$+)$4??(B??8E
)G4A74E7BA6B78F4A7HC
This ball bearing equipped incoming bushing can be
used in place of the standard incoming wire bushing,
when feeding solid steel or cored wire electrodes. It
significantly reduces any abrasion to the electrode
wire where it enters the feed head. This results in
even smoother, more trouble free operation.
+*%$
-($$
