Filter
Top Products
XT485 Treadmill
18
USER PROGRAMS
STEP 1:Press the User 1-2 key once for User 1 or twice for User 2 then
press Enter. Note that the dot matrix display portion will have a single row of
segments at the bottom (Unless there is a previously stored program).
STEP 2: The Message Center will now be blinking an Age value. Adjust the
age and press Enter.
STEP 3: The Message Center will now be blinking a bodyweight value. Enter
your bodyweight and press Enter.
STEP 4: Note the clock/Message Center is ashing. Use the Adjust + or -
keys to adjust up from 30 minutes (if desired). Press the Enter key. This is a
must to continue even if time is not adjusted.
STEP 5: The rst column (segment) will now be blinking. Using the + or -
keys, adjust the speed level to your desired effort for the rst segment then
press enter. The second column will now be blinking. Repeat the above
process until all 20 segments have been programmed. The rst column will
be blinking again. This is for the incline programming. Repeat the above
process to program all 20 segments for incline.
STEP 6: Press the Start button to begin the workout and also save the program to memory or press
Enter to go back one step to reprogram.
CALORIE PROGRAM
STEP 1: Press the Calorie key. Press Enter to select the program. The display will prompt you
through the programming.
STEP 2: If Enter was pressed, the Message Center will now be blinking a value, indicating your Age
(default is 35). Entering your correct age affects the heart rate Bar Graph Display and the Heart Rate
programs. Use the + or - keys to adjust, then press Enter. Your age determines your
recommended maximum heart rate. Since the Bar Graph Display and the Heart Rate features are
based on a percentage of your maximum heart rate, it is important to enter the correct age for these
features to work properly.
STEP 3: The Message Center will now be blinking a value, indicating your Body Weight (default is
150#). Entering the correct body weight will affect the calorie count. Use the + or - keys to adjust,
then press Enter.
A note about the Calorie display: No exercise machine can give you an exact calorie count because
there are too many factors which determine exact calorie burn for a particular person. Even if
someone is the exact same body weight, age and height, their calorie burn may be very different than
yours. The Calorie display is to be used as a reference only to monitor improvement from workout to
workout.
STEP 4: The Message Center displays “Use + or – keys to adjust Calorie burn” (default is 300) After
adjusting, press Enter.
STEP 5: The Message Center will now be blinking the preset top speed of the selected program
(3 mph or 5 kph). Use the + or - keys to adjust, then press Enter. Each program has various speed
changes throughout; this allows you to limit the highest speed the program can reach.
STEP 6: The Message Center will be blinking the preset top incline of the selected program (1.0%).
Use the Incline + or – keys to adjust, then press Enter.
STEP 7: The Message Center displays the Program Time ( a value that that was determined by the
data you entered in steps 2-6); Press Start to accept the calculated Time or Enter to return to steps
3-5 and change the data, which will recalculate the Program Time.
• When the Start key is pressed, the program begins with a 3:00 warm up (1:00 @ 1mph, 1:00 @ 2mph, and
1:00 @ 3mph) or you have the option of pressing the Start again to bypass and begin the workout.
• When the program begins both the Calorie and Time windows will count down to 0. If the Time expires
before calories burned reaches 0, the Time window will begin accumulated time, until Calories reach 0.
• After the program has ended, there will be a 3:00 cool down (1:00 @ 1mph, 1:00 @ 2mph, and 1:00 @ 3mph)
or you have the option of pressing the Stop key to end the workout.