Filter
Top Products
o_
7.
9.
L
Plug together both
of the Base Rail
Wire Harness
(8)
to
lower
ends of the
Spiral
Signal Cables
(46)
located
just
under
the
perforated
Slider Shields
on back of the Screen
Panels
(53).
Attach the two Rear Support
Rails
(4)
to the Lower
Cross Brace
(3)
and the Cross Brace Backing Plates
(13)
using four bolts
(28),
eight washers
(18)
and four nuts
(20)
as shown. HAND
TIGHTEN
the bolts at this time.
Attach the
two Big Pulleys
(27)
to the
two Upper
Linking Plates
(17)
using
two bolts
(19),
four
washers
(23)
and two
nuts
(26)
as shown.
HAND TIGHTEN the bolts at this time.
Lift the Upper Linking
Plates Assembly
(17
& 271
and
place
it on top of the Left Upright Guidepost Assembly
(9,
12, 53), and attach the two
Upper Linking Plates
(17)
to the Left Upright Guide Post
(12)
using
two bolts
(22),
four washers
(18)
and two
nuts
(20)
as shown. HAND
TIGHTEN
the bolts at this time.
'10.
Carefully
flex the Left Weight Bar Cables
(24)
onto the
pulleys
(27)
so that the cables insert into the
grooves
of each corresponding
pulleys
and allowing the
Left Weight Bar Knuckle
(44)
to
hang free.
Be sure that the
cables are straight and uncrossed and cables
and
pulleys
move smoothly.
1 1. Align the holes on top of the
Rear Support Rail
(4)
with the corresponding holes on the
two Upper Linking
Plates
('17)
and attach the Rear Support
Rail
(4)
to the Linking Plates
(17)
using two
bolts
(22),
four
washers
(18)
and two nuts
(20)
as shown.
HAND TIGHTEN the bolts at this time.
12. Repeat the steps 8
-
1 1
on the
right
side of the
PROSPOTT/rressrM P-'l00.
13. Attach the Upper Cross
Brace
(11)to
the four Upper linking Plates
(17)
using four bolts
(22),
eight washers
(18)
and four nuts
(20)
as shown. HAND
TIGHTEN the bolts at
this
time.
14.
Tighten all bolts and
nuts
used for assembly
in
previous
steps.
STEP
#2: SENSOR WEIGHT BAR INSTALLATION
1. Standing in front
of
the PROSPOTlaessrM P-100. Insert one end
and then the other end of the Sensor
Weight Bar
(25)
into the Knuckles
(42
& 44).
Slide
the knuckles
onto the
Bar
untrl they
rest
snugly against
the
preinstalled
sensor retaining collars
(45
& 48) at each end of the Sensor Weight Bar
(25). (There
is
a
rotation limiting
pin
that
protrudes
from the bottom of the Sensor Weight Bar
(25)
that
must
fit through a slot
in the knuckles
U2
& 44\
as
it is slid into
position).
2. Place
one
Plastic
Locking Sleeve
(39)
onto each end of the Sensor Weight Bar
(25)
and slide them inwards
until they butt up
against and secure the
Weight Bar
Cable
Knuckle
in
place.
Tighten Plastic Locking
Sleeve
bolts securely.
3. Place
one of the Olympic Adapters
(30)
onto the Sensor
Weight
Bar
(25)
and slide them
onto the Bar until
they touch the Plastic Locking Sleeves
(39).
lnsert an Olympic Adapter Retaining
Plug
(33)
onto
each end
of the Sensor Weight Bar
(25)
so that they also
go
inside of
the Olympic Adapters
(30).
Secure with
two
Allen bolts
(29)
and two washers
(36).
4. Attach the four
small
plastic pipes (15)
to the four Upper linking Plates
(17)
using
four
bolts
(34),
eight
washers
(38)
and four nuts
(35)
as shown. Tighten the bolts securely.
5. Attach the Electronic Box Locating Board
(40)
to the Lower Cross Brace
(3)
using two bolts
(22),
tour
washers
(18)
and
two
nuts
(20)
as shown. Tighten the bolts securely.
6. Attach the six
Side
Weight
Plate Holders
(14)
to the Rear
Support
Rails
(4)
using six
backing
plates (16),
twelve
bolts
(22),
twenty-four washers
(18)
and twelve nuts
(20)
as shown. Tighten
the bolts securely.
Note: In this manual when
referring to Left and Right side of unit,
the left and right
perspective
are from the outside,
facing the front of the unit.
--2--