Filter
Top Products
835101 HIP SLED ASSEMBLY INSTRUCTIONS
Pull back the SPRING PIN on the PLATFORM SLEEVE and insert the PLATFORM ADJUSTMENT
into it. Slide the PLATFORM ADJUSTMENT down to the first adjustment hole and release the SPRING
PIN.
Assemble the PLATFORM ADJUSTMENT to the PLATFORM as shown on drawing using one (1) 1/2
X 4 IN. BOLT, and one (1) 1/2 IN. LOCK NUT. (TIGHTEN THE CONNECTION ENOUGH
REMOVE THE PLAY, YET ALLOWING THE PLATFORM ADJUSTMENT TO ROTATE
FREELY)
SECURELY assemble the LEFT and RIGHT HANDLES to the BASE on tkeir respective sides as shown
on drawing using four (4) 3/8 X 3 IN. BOLTS, eight (8) 3/8 IN. WASHERS, and four (4) 3/8 IN.
NUTS.
10. Slide two (2) 1 X 5 IN. GRIPS over the ends of the LEFT and RIGHT HANDLES as shown on drawing.
11.
Place two (2) 2 IN. SQ. COVER CAPS on each end of the base 0fthe REAR UPRIGHT.
12.
13.
14.
15.
16.
17.
18.
19.
20.
SECURELY assemble the REAR UPRIGHT to the BASE WELDMENT as shown on drawing using
two (2) 1/2 X 3-1/4 IN. BOLTS, four (4) 1/2 IN. WASHERS, and two (2) 1/2 IN. LOCK
LOOSELY assemble the LEFT and RIGHT RAILS, along with the SEAT PAD to the BASE
WELDMENT as shown on drawing using two (2) 3/8 X 4-1/2 IN. BOLTS, two (2) 3/8 IN.
WASHERS, and two (2) 3/8 IN. WASHERS. Temporarily assemble the RAII,S to the REAR UPRIGHT
using two (2)1/2 X 4-1/2 IN. BOLTS to aid in the assembly of this step.
Insert four (4) 2 IN. SQ. END CAPS into the each end of the CARRIAGE as shown on drawing.
SECURELY assemble four (4) 3 IN. DIA. WHEELS to the sides of the CARRIAGE as shown
drawing using four (4) 1/2 X 4-1/2 IN. BOLTS, eight (8) 1/2 IN. WASHERS, and four (4) 1/2 IN.
HEIGHT LOCK NUTS.
SECURELY assemble two (2) 2 IN. DIA. WHEELS to the BRACKETS on the left side of the
CARRIAGE as shown on drawing using two (2) 3/8 X 2 IN. BOLTS, four (4) 3/8 IN. WASHERS,
two (2) 3/8 IN. LOCK NUTS.
Assemble the two (2) ADJ. WHEEL BRACKETS to the right side of the CARRIAGE as shown
drawing using two (2) I/2 X 2-3/4 IN. BOLTS, two (2) 1/2 IN. WASHERS, and two (2) 1/2 IN.
HEIGHT LOCK ~UTS. (NOTE: TIGHTEN BRACKETS SECURELY TO THE CARRIAGE, THEN
BACK NUT OFF’l/2 TURN TO ALLOW FOR ADJUSTMENT IN A LA’fTER STEP)
SECURELY assemble two (2) 2 IN. DIA. WHEELS to the ADJ. WHEEL BRACKETS on the right side
of the CARRIAGE as shown on drawing using two (2) 3/8 X 2 IN. BOLTS, four (4) 3/8 IN. WASHERS,
and two (2) 3/8 IN. LOCK NUTS.
Attach one (1) 4 X 14 IN. NON SKID STRIP to the HORIZONTAL TUBE of the CARRIAGE as shown
on drawing.
Remove the two temporary 1/2 X 4-1/2 IN. BOLTS from (STEP 13). Swing the LEFT and RIGHT
RAILS out enough to insert the CARRIAGE ASSEMBLY in between them. Allow the CARRIAGE to
rest on the SAFETY STOPS underneath the RAILS. SECURELY assemble the RAILS to the REAR
UPRIGHT as shown on drawing, using the two (2) 1/2 X 4-1/2 IN. BOLTS, foyer (4) 1/2 IN. WASHI~RS,
and two (2) 1/2 IN. LOCK NUTS.
5
10/09/95