Horizon Fitness GS 1035T Treadmill User Manual


  Open as PDF
of 19
 
32
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
33
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
PROBLEM: The treadmill circuit breaker trips during a workout.
SOLUTION: Verify the following:




PROBLEM: The running belt does not stay centered during a workout.
SOLUTION: Verify the following:


PROBLEM: Operating speed appears inaccurate.
SOLUTION: Auto-calibrate the treadmill:

console. Press and hold the elevation “+” and speed “-” buttons for
approximately 5 seconds to enter the Engineering Mode. The console
will beep and “ENG0” appears in the display.


running belt will begin to move automatically and the auto-calibration
sequence will properly set and store the speed values.

console will automatically exit Engineering Mode and return to the
start-up screen.
TROUBLESHOOTING - HEART RATE
Check your exercise environment for sources of interference such as fluorescent lights, computers, underground fencing, home
security systems or appliances containing large motors. These items may cause erratic heart rate readouts.
You may experience an erratic readout under the following conditions:
Gripping the heart rate handlebars too tight. Try to maintain moderate pressure while holding onto the heart rate handlebars.
Constant movement and vibration due to constantly holding the heart rate handlebars while exercising. If you are receiving
erratic heart rate readouts, try to only hold the grips long enough to monitor your heart rate.
When you are breathing heavily during a workout.
When your hands are constricted by wearing a ring.
When your hands are dry or cold. Try to moisten your palms by rubbing them together to warm.
Anyone with heavy arrhythmia.
Anyone with arteriosclerosis or peripheral circulation disorder.
Anyone whose skin on the measuring palm is especially thick.
If the above troubleshooting section does not remedy the problem, discontinue use and turn the power off.
PLEASE CALL CUSTOMER TECH SUPPORT AT THE NUMBER ON THE BACK PANEL.
The following information may be asked of you when you call. Please have these items readily available:
 Model Name
 
 
In order for Customer Tech Support to service your treadmill they may need to ask detailed questions about the symptoms that are
occurring. Some troubleshooting questions that may be asked are:
 
 
 
chirping etc.)?
 
Answering these and other questions will give the technicians the ability to send proper replacement parts and the service necessary
to get you and your Horizon Fitness treadmill running again!
MAINTENANCE
WA RNING
DO NOT stand on running belt while
calibrating – stand on the guide
rails. Treadmill will fluctuate between
low and high speeds for several
minutes until calibration is complete.
Cleanliness of your treadmill and its operation environment will keep maintenance problems and service calls to a
minimum. For this reason, we recommend that the following preventive maintenance schedule be followed.
AFTER EACH USE (DAILY)
Clean and inspect, following these steps:
Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
Wipe down the running belt, deck, motor cover, and console casing with a damp cloth. Never use solvents, as they
can cause damage to the treadmill.
Inspect the power cord. If the power cord is damaged, contact Horizon Fitness.
Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut.
Check the tension and alignment of the running belt. Make sure that the treadmill belt will not damage any other
components on the treadmill by being misaligned.
EVERY WEEK
Clean underneath the treadmill, following these steps:
Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
Fold the treadmill into the upright position, making sure that the lock latch is secure.
Move the treadmill to a remote location.
Wipe or vacuum any dust particles or other objects that may have accumulated underneath the treadmill.
Return the treadmill to its previous position.
EVERY MONTH - IMPORTANT!
Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
Inspect all assembly bolts of the machine for proper tightness.



do so may result in premature failure of key electrical components.

the unit. These particles may accumulate from normal treadmill use.
EVERY 6 MONTHS OR 150 MILES
It is necessary to lubricate your treadmill running deck every six months or
150 miles to maintain optimal performance. Once the treadmill reaches

The treadmill will not operate while the message is showing. Hold Stop for
5 seconds to suspend message for 5 miles. Your treadmill came with a
bottle of lubricant which can be used for two applications. If you need
lubricant, contact Horizon Fitness. Only use lubricant provided by
Horizon Fitness.

at the wall outlet.

marks on both sides of the frame and note roller position). Once the belt
is loosened, take the bottle of lubricant and apply it to the entire top
surface of the running deck. Tighten both rear roller bolts (matching up
the marks for proper position) to original position. After you have applied
lubricant, plug in the power cord, insert the safety key, start the treadmill
and walk on the belt for two minutes to spread the lubricant.


Please contact Horizon Fitness with questions about applying lubricant to your treadmill.
RUNNING BELT
RUNNING DECK
LUBRICATION
GS_1035T_Treadmill_Rev.2.3.indd 32-33 6/13/07 11:20:06 AM
 previous next