Filter
Top Products
11
CONSOLE DESCRIPTION
Refer to the drawing on page 10. Note: If there is a
thin sheet of clear plastic on the face of the con-
sole, remove it.
A. Program profiles—These profiles show how the
resistance of the exercise cycle and the target pace
will change during Smart programs and Heart Rate
programs. For example, profile number 3 shows
that during Smart program 3, both the resistance
and the pace will gradually increase during the first
half of the program, and then gradually decrease
during the last half.
B. Exercise feedback display—This display features
seven modes that give you instant exercise feed-
back: your current speed, the elapsed time (or the
time remaining in a Smart program or a Heart Rate
program), the distance that you have pedaled, the
resistance level, the approximate number of calo-
ries you have burned, the approximate number of
fat calories you have burned (see FAT BURNING
on page 21), and your heart rate (when you use the
handgrip pulse sensor). If the scan mode is select-
ed, the display will change from one mode to the
next every six seconds. Or, you can select a single
mode for continuous display.
Note: The console can show speed and distance
in either miles or kilometers. To change the unit
of measurement, hold down the On/Reset button
for six seconds. The mode indicators (see E
below) will show which unit of measurement is
selected. When the batteries are replaced, it may
be necessary to reselect the desired unit of mea-
surement.
C. Increase and decrease arrows—During Smart pro-
grams, Heart Rate programs, and iFIT.com pro-
grams, these arrows will prompt you to increase or
decrease your pace to match the target pace.
D. Manual mode/program indicator—When a Smart
program is selected, the upper right corner of the
display will show a 1, 2, 3, 4, 5, 6, 7, or 8, depend-
ing on which Smart program is selected. When a
Heart Rate program is selected, the upper right cor-
ner of the display will show a 9 or 10. When the
iFIT.com mode is selected, the upper right corner
will show the letters IF. When the manual mode is
selected, the upper right corner will be blank.
E. Feedback mode indicators—These indicators show
which feedback mode (scan, speed, time, distance,
resistance level, calories, fat calories, or heart rate)
is currently shown. Note: When the distance is
shown, the word Miles or the letters Kms will
appear; when your speed is shown, the letters MPH
or Km/H will appear.
F. Pace indicators—When the manual mode is select-
ed, only the left pace indicator will appear. This
pace indicator represents your exercise pace. As
you increase or decrease your pace, additional bars
will appear or disappear on the pace indicator. When
a Smart program, a Heart Rate program, or the
iFIT.com mode is selected, both pace indicators will
appear. The left pace indicator represents your
exercise pace, and the right pace indicator repre-
sents a target pace. During the program, the target
pace will periodically change. As the right pace
indicator changes, simply adjust your pace so that
the same number of bars appear on both pace indi-
cators. Important: The target pace is a goal
pace. Your actual pace may be slower than the
target pace, especially during the first few
months of your exercise program. Make sure to
exercise at a pace that is comfortable for you.
G. On/Reset button—When the console is off, pressing
this button will turn on the display. When the console
is on, pressing this button will reset the display.
This button is also used to select the unit of mea-
surement for speed and distance (see B at the left).
H. Display Mode button—This button is used to select
the feedback modes. The modes will be selected in
the following order: scan, speed, time, distance,
resistance level, calories, fat calories, and heart
rate (when the handgrip pulse sensor is used).
I. + and – buttons—These buttons control the resis-
tance of the exercise cycle. There are ten resis-
tance levels; level 10 is the most challenging.
These buttons are also used to enter your age
when a Heart Rate program is selected.
J. Program button—This button is used to select the
manual mode, Smart programs, and Heart Rate
programs.
K. IFIT.com button—This button is used to select the
iFIT.com mode. The indicator on the button will light
when the iFIT.com mode is selected.
To use the manual mode of the console, refer to
page 12. To use a Smart program, refer to page 13.
To use a Heart Rate program, refer to page 14. To
use iFIT.com CD’s or videos, refer to page 18. To
use a program directly from our Web site, refer to
page 19.