Filter
Top Products
Operation Guide 5182
E-40
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 29 time
zones around the globe. Each time zone has a “city code”, which is a three-letter
abbreviation of a representative city in the zone. The representative city of the time
zone that is currently selected in the World Time Mode is called the “World Time City”.
Hand Functions
x
Second Hand: Indicates the currently selected World
Time City.
v
Left Dial Hand: Indicates the summer time setting
(STD, DST) for the currently selected
World Time City.
b
Right Dial Hands: Indicate the current time in the
selected World Time City in 24-hour
format.
>
@ *
E-41
To view the time in another time zone
Use 1. C to rotate the v
v
Left Dial Hand until WT is located next to the pointer ( ).
This indicates the World Time Mode.
x
Use 2. D to move the
x
Second Hand to the city code you want to select as the
World Time City.
The
x
b
Right Dial Hands will move to the current time in the currently selected
World Time City. At this time, the
z
Hour Hand and
c
Minute Hand will continue
to indicate the current time in the Home City.
Holding down
x D causes the
x
Second Hand to move at high speed.
For full information on city codes, see the “City Code Table” at the back of this x
manual.
If you think that the time indicated for the selected World Time City is not correct, x
it probably means that there is something wrong with your Home City settings.
Use the procedure under “To confi gure summer time and other Home City
settings” (page E-24) to correct the Home City settings.
E-42
To specify standard time or daylight saving time (DST) for a time zone
In the World Time Mode, use 1. D to select the city code
for the time whose setting you want to change.
Press 2. B to toggle the v
v
Left Dial Hand between STD
(standard time) and DST (daylight saving time).
Note that you cannot switch between
x STD (standard
time)/DST (daylight saving/summer time) while UTC is
selected as the World Time City.
Note that the x STD (standard time)/DST (daylight
saving/summer time) setting affects only the currently
selected time zone. Other time zones are not affected.
B
>
E-43
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
The following example shows what happens when the Home City and World Time
City are swapped while the Home City originally is TYO (Tokyo) and the World Time
City is NYC (New York).
Home City World Time City
Before swapping
Tokyo
10:08 p.m.
(Standard time)
New York
9:08 a.m.
(Daylight saving time)
After swapping
New York
9:08 a.m.
(Daylight saving time)
Tokyo
10:08 p.m.
(Standard time)
E-44
To swap your Home City and World Time City
In the World Time Mode, use 1. D to select the World
Time City you want.
In this example, you would move the
x x
x
Second Hand
to NYC in order to select New York as the World
Time City.
Wait until the
x
b
Right Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
*@
E-45
Hold down 2. A for about three seconds until the watch
beeps.
This will make the World Time City (
x NYC in this
example) your new Home City. At the same time, it
will change the Home City you had selected prior to
step 2 (TYO in this example) to your World Time City.
After swapping the Home City and World Time City,
x
the watch will stay in the World Time Mode. The
x
x
Second Hand will point to your new World Time City
(TYO in this example).
The
x
b
Right Dial Hands will indicate the current time
in your new World Time City.
@
*
E-46
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
Hand Functions
x
Second Hand: Indicates the current alarm ON/OFF
setting.
v
Left Dial Hand: Points to AL.
b
Right Dial Hands: Indicate the current alarm time
setting in 24-hour format.
>
*@
E-47
To change the alarm time setting
Use 1. C to rotate the v
v
Left Dial Hand until AL is located next to the pointer ( ).
This indicates the Alarm Mode.
x
Use 2. D (+) and B (–) to change the alarm time setting.
Each press of either button will move the x
b
Right Dial Hands one minute.
Holding down
x D or B will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
The alarm always works based on the time kept in the Timekeeping Mode.
x
The watch will return to the Timekeeping Mode automatically if you do not x
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm on and off. The
x
Second Hand will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
E-48
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or date of the watch to be off.
If this happens, perform the applicable home position adjustment procedures in this
section.
Hand home position adjustment is not required if the time and day settings are
x
correct.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in the home position adjustment mode. In either case,
any adjustments you made before the watch returned to the Timekeeping Mode will
be applied.
E-49
To adjust home positions
Use 1. A as shown under “Setting Modes” (page E-20) to
enter the “Home Position Adjustment” mode.
The watch will exit the home position adjustment mode
x
automatically if you do not perform any operation for
about two or three minutes.
First is
x v
v
Left Dial Hand home position adjustment.
If the
x
v
Left Dial Hand moves to 12 o’clock, it is in
the correct home position. If it doesn’t, use D (+) and
B (–) to move it to 12 o’clock.
@B +
*> 56