7
Disc
Management
Recording PlaybackIntroduction Connections Basic Setup Editing Function Setup VCR Function
Others
TROUBLESHOOTING
Symptom Remedy
D
V
D
•
V
C
R
DV si
na
cannot
e input
Be
ore connection, turn on the
ower su
lies
or both this unit and the
VC, and make sure that these units are in sto
mode
Only a “DVC-SD” signal can be input from the DVC to this unit. Other
pes of signals are not supported
Do not connect an
device other than the DVC. Even i
a recorder or PC
ith another DV terminal is connected, the DV function will not o
erate
If the DVC is not recognized after connection, turn off the power suppl
r
h
ni
n
r
-
nn
h
DV
he DVC cannot be o
erated with this
ni
Signal input or DVC operation from this unit ma
be disabled
epending on the t
pe of DVC
If a DVC si
nal cannot be input, use an external input (L1 (Rear)/L2
front)) for analo
connection via audio/video cables
DVC control ma
be disabled depending on the t
pe o
DVC, even in a
ode other than camera mode. In this case
switch to DVD control and
xecute the normal recordin
procedure while operatin
the DVC
Certain
unctions o
the unit cannot
opera
e
Some
unctions may not operate depending on the type o
DVC. For
xample, i
the DVC does not support slow playback mode, the slow
layback
unction is disabled
Wit
L3 (DV-IN), t
e
isc
isp
ay menu
oes not appear un
ess
isc
ay
ac
is execute
DV audio si
nal cannot be switched
For recordin
with the DVC, the recordin
audio si
nal can be set to 12
its or 16 bits. However, when 16-bit recordin
mode is selected, audio
i
nal cannot be switched. To record an audio si
nal, set it to 12 bits
No ima
e from HDMI connection
Check the HDMI connection.
Check the status of the HDMI related
ndications.
Check whether the connected monitor device or other device su
orts
DCP. (This unit will not output a video si
nal unless the other device
u
orts HDCP.
Check the settin
of HDMI.
Check whether the out
ut format of this unit (HDMI FORMAT) matches
he su
orted in
ut
ormat o
other connected device
I
the unit is connected to the unauthorized display device with an
DMI ca
e, t
e au
io/vi
eo signa
may not
e output w
en p
aying
ac
a commercia
DVD-vi
eo
D
V
D
ere is no
icture
I
the setu
menu a
ears on the TV screen,
ress
RETURN
x
Check i
the progressive scan mode is set correctly according to your TV
age
icture noise appears
• C
ean t
e
isc wit
a c
eaning c
ot
Pla
back picture from the external
vi
nn
hi
ni
i
i
r
• If the picture output si
nal from the external devices passes throu
h this
nit to get to
our TV, the cop
protection signal applied to some DVD could
ffect the picture qualit
. Disconnect the pla
back device in question and
onnect it directl
to
our TV.
h
r
i
n
n
• I
ou are using DIGITAL AUDIO OUTPUT (COAXIAL) jack, check the setting
n “Au
io Out” (pa
e 87).
• C
ean t
e
isc wit
a c
eanin
c
ot
Soun
is noisy
• C
ean t
e
isc wit
a c
eaning c
ot
he disc does not pla
back
• N
i
i
in
r
• A
l
nk
i
i
in
r
• The disc is upside down. Insert the disc with the labeled side facin
up
• The disc is not correctl
inserted
• The unit cannot pla
back certain discs (such as a CD-ROM) (page 10)
• The re
ion code on the DVD-video does not match the unit (pa
e 10)
• M
i
r
h
n
n
in
i
h
ni
R
m
v
h
i
n
l
v
h
nit turned on for about 2 hours until the moisture evaporates (pa
e 3)
• If the disc was recorded on another recorder, the unit cannot pla
bac
h
i
if i
w
n
fin
liz
Playback image
reezes
or a second. • During the playback o
2 layered disc, picture may
reeze
or a moment
hen the 1st layer switches to the 2nd layer. This is not a mal
unction.
Di
r
r
n
i
ni
nn
p
aye
ac
on ot
er DVD p
ayers
• I
you are using DVD-RW/-R or DVD+R, please ensure you
inalized the
isc a
ter recording (pages 31 - 33).
