Filter
Top Products
7. Attach the two
Front
Uprights
(4)
to the two base
rails
(1
&
2)
using the Upright Support Plates
(6),
eight
bolts
(28),
sixteen
washers
(18)
and eight nuts
(20)
as shown. HAND TIGHTEN
the bolts at
this time.
8. Attach the two
Pulley
Support
Frames
(17)
to the
Front
Uprights
(4)
and the
Upright Guide Posts
(10
& 12)
using eight
bolts
(22),
sixteen washers
('18)
and
eight nuts
(20)
as
shown. HAND TIGH-f EN
the bolts at this
time.
9. Attach the Upper Cross Brace
(1
1
)
to the two Pulley Support Frames
(17)
using eight
bolts
(52),
sixteen
washers
(18)
and eight nuts
(20)
as shown.
HAND TIGHTEN the bolts at this
time.
10. Tighten all bolts and nuts used for assembly
in
previous
steps.
11 Carefully flex the Left Weight Bar Cables
(24)
onto the
pulleys
(27)
so that the cables insert
into the
grooves
of each corresponding
pulleys
and
insert
the
Left \ ieight Bar Knuckle
(44)
down through
the rectangular
cutout in the
Pulley
Support
Frame
(17)
and
allowing
the Left Weight
Bar
Knuckle
(44)
to hang free.
Be sure
that the cables are straight and uncrossed and cables and
pulleys
move
smoothly.
12. RFrpeat
the step
1 1
on the right side of the PROSPOTlrrrrersrM
PC3000.
STEP #2: SENSOR WEIGHT BAR INSTALLATION
1. Standing in front of the PROSPOTltzessrM PC3000. Insert one
end and then the other
end of the
Sensor
\
Jeight Bar
(25)
into
the
Knuckles
(42
& 44],. Slide the knuckles
onto the Bar until
they
rest
snugly
against
the
preinstalled
sensor retaining
collars
(45
&
48) at
each end of the Sensor Weight
Bar
(25). (There
is a
rotation
limiting
pin
that
protrudes
from the bottom of the Sensor Weight Bar
(25)
that must
fit through
a slot
in the knuckles
(42
& 44) as it is slid into
position)
2. Place
one
Plastic Locking
Sleeve
(39)
onto each end of the Sensoi Weight Bar
(25)
and slide
them inwards
until they
butt
up
against and secure the
Weighi Bar
Cable Knuckle in
place.
Tighten
Plastic Locking
Sleeve
boits
securely.
3. Piace one of the Olympic Adapters
(30)
onto the Sensor Weight
Bar
(25)
and
slide them onto
the Bar until
they touch the
Plastic
Locking Sleeves
(39)
Insert an Olympic Adapter
Retaining Plug
(33)
onto each
end
of the Sensor Weight Bar
(25)
so that they also
go
Inside of
the Olympic Adapters
(30).
Secure
with two
Allen bolts
(29)
and two washers
(36).
4.
Aitach the four small
plastic pipes (15)
to the two Pulley Support Frames
(17)
using
four
bolts
(34),
eight
washers
(38)
and four nuts
(35)
as shown. Tighten the bolts securely.
5. Attach the eight
Side
Weight
Plate Holders
(14)
to the two Front
Uprights
(4)
using sixteen
bolts
(53),
thirty-
tvro washers
(18)
and sixteen nuts
(20)
as shown. Tighten the
bolts securely.
Note: In this manual when referring
to Left and Right side
of unit, the left and right
perspective
are from the outside, facing
the front of the unit.
--2--