Filter
Top Products
Instructions
for
Assembly of
the PROSPOT/tnessrM
PC3000
Before assembly, choose a safe
location for
your
PROSPOTJitnessn
PC3000. The PROSPOTlrzessrs
PC3000 has a footprint of approximately 6'x 6'.
The
barbell is approximately 7'
long. Locate
your
PROSPOTfrne"^srt PC3000 away
from
any source
of water. Do not
allow any liquid
to be
near
the machine
or spilled on any electrical
part.
Do not insert any object into the electrical
box.
Approximate assembly time
is
1/2
hours.
A flat area of 8' x 8' will be required to assemble
and
properly
use the PROSPOTlrzessw
PC3000.
You will need the following tools and a helper to complete the assembly:
.
5 mm Allen Wrench
.
14 mm Box End Wrench
.
17 mm Box End Wrench
.
19 mm Box End Wrench
Floor Padding, such as cardboard,
to avoid scratching
your
floor
during assembly.
A
good pair
of scissors will be helpful in separating the
parts
from
one another while
removing
them
from
the
cartons.
HAND TIGHTEN
all bolts. DO NOT
fully
tighten bolts until instructed
to do so.
Before assembly, separate and identify
the
righFsided
parts
from the left-sided
parts.
These
parts
are easily
distinguished
by the
manner in
which the
pre-drilled
holes align with
corresponding
parts,
or are identified
by
"L"&"R"stickers.
The PROSPOTliaressrM
PC3000 uses
several different
lengths
of bolts. Be
careful to use the
correct length
of bolt called for at each step of
assembly. Refer to the sizing charts
provided.
.
WARNING: Never
perform
any maintenance
on the PROSPOTJitnessrM
PC3000
while the Power
Supply
is
plugged
into
the wall !!!
STEP # 1:
MAIN FRAME ASSEMBLY
1. Place
the two Base Rails
(1
&
2)
opposite each other in the center
of the assembly
area as shown in
the
lllustration.
Place the Lower Cross Brace
(3)
between the two Base Rails
(1
& 2) so
that the side
pre-drilled
holes
ofthe Base Rails
(1
& 2) align with
the end
holes
of the Lower
Cross Brace
(3).
2.
Carefully thread the
Cross
Brace Wire
Harness
(8)
through
the corresponding
side
pre-drilled
holes
of the
Base Rails
(1
& 2) then
pull
the
Wire Harness
(8)
out of the top holes
of the Base Rails
('1
& 2).
3.
Attach
the two Base Rails
(1
& 2) to the Lower Cross Brace
(3)
using two Cross Brace
Backing Plates
('13).
four
bolts
(28),
eight washers
(18)
and four
nuts
(20)
as shown. HAND
TIGHTEN
the bolts at
this time.
4.
Attach the Right
Upright Guidepost Assembly
(7
,
10, 23)
to the Lower
Cross Brace
(3)
and the Cross Brace
Backing Plate
(13)
attached on the right base rail
(1)
using two bolts
(28),
four
washers
(18)
and two nuts
(20)
as shown.
HAND TIGHTEN the bolts
at this time.
5. Attach
the Left Upright Guidepost
Assembly
(9,
12,23) to the Lower
Cross Brace
(3)
and the Cross
Brace
Backing Plate
(13)
attached on the left base rail
(2)
using
two bolts
(28),
four washers
(18)
and
two nuts
(20)
as shown. HAND TIGHTEN
the bolts at this
time.
6. Plug
together both of the Cross Rail Wire
Harness
(8)
to lower ends
of the Spiral Signal
Cables
(46)
located
just
under the
perforated
Slider Shields on back of the
Screen
Panels
(23).
I