Filter
Top Products
710
¥ Distance (DIST)ÑThis mode shows the total num-
ber of miles you have cycled, up to 999. The display
will then reset to zero and continue counting.
¥ LapsÑThis mode shows the number of quarter-mile
laps you have completed.
¥ Calories (CAL)ÑThis mode shows the approximate
number of calories you have burned.
STEP-BY-STEP CONSOLE OPERATION
Before the console can be operated, the batteries
must be installed. (See assembly step 12 on page 7
for installation instructions.) Follow the steps below to
operate the console.
Turn on the power
To turn on the
power, press the
on/reset button or
simply begin exer-
cising. When the
power is turned on,
the entire display
will appear for two seconds. The console will then
be ready for use. Note: If batteries were just
installed, the power will already be on.
Select one of the three pacer programs or the
manual mode
When the power is
first turned on, the
console will be in
the manual mode.
To select one of the
pacer programs,
repeatedly press
the program button.
The program indi-
cator will show
which program you
have selected. The
programs will be selected in the following order:
the manual mode, the 6 MPH/30 RPM program,
the 12 MPH/60 RPM program, and the 18 MPH/
90 RPM program. Note: Once you select a pacer
program, you can reselect the manual mode by
repeatedly pressing the program button.
Begin your workout
If you selected the manual mode, one indicator on
the inner P.A.C.E.R. track will light. As you exer-
cise, this indicator will move around the quarter-
mile track.
If you selected a
pacer program, two
indicators on the
P.A.C.E.R. track will
light. The indicator
on the inner track
will show your actual
pace. The indicator
on the outer track
will move around the track at the programmed
pace. As you exercise, adjust your pace so that
the indicators on the inner and outer tracks
remain even. As the program progresses, the tar-
get pace will change periodically; as the target
pace changes, you should also adjust your pace.
Important: The target pace is a goal pace. Your
actual pace may be slower than the target
pace, especially during the first few months of
your exercise program. Be sure to exercise at
a pace that is comfortable for you.
Follow your progress with the monitor modes
When the power is
turned on, the con-
sole will scan
through the five
modes automatically.
A flashing mode indi-
cator will show which
mode is currently dis-
played. When the Laps mode is displayed, an ÒLÓ
will also appear. If desired, the display can be
reset by pressing the on/reset button.
The exercise cycle
also features an
innovative handgrip
pulse sensor. The
pulse display allows
you to monitor your
heart rate during your workout. To use the pulse
sensor, see page 11.
Turn off the power
To turn off the power, simply wait for about six
minutes. If the pedals are not moved and the
console buttons are not pressed for six minutes,
the power will turn off automatically.
5
4
3
2
1
Target
Pace
Actual
Pace
Mode Indicator
10. Attach the Backrest (15) to the Seat Bracket (69)
with four M6 x 16mm Hex Head Screws (24).
11. Identify the Left Pedal (45) (there is an ÒLÓ on the
Left Pedal for identification). Using an adjustable
wrench, tighten the Left Pedal counterclockwise into
the left arm of the Crank (29).
Tighten the Right Pedal (not shown) clockwise into
the right arm of the Crank (29).
Adjust the Pedal Strap (27) on the Left Pedal (45) to
the desired position. Press the Pedal Strap onto the
adjustment tab on the Left Pedal.
Adjust the Pedal Strap on the Right Pedal (not
shown) in the same manner.
15
24
69
29
27
45
Tab
10
11
9. Attach a Seat Handle (17) to the Seat Bracket (69)
with two M6 x 38mm Button Head Bolts (18) and
two M6 Nylon Locknuts (66).
Attach the other Seat Handle (17) to the Seat
Bracket (69) in the same manner.
69
17
18
66
17
9
12. The Console (8) requires either two or three ÒAAÓ
batteries (not included); alkaline batteries are
recommended. Open the battery cover (not shown)
on the back of the Console. Press the batteries into
the battery clip. Make sure that the negative (Ð)
ends of the batteries are touching the springs.
Close the battery cover. Note: If the battery clip
holds three batteries, you must insert three batteries.
8
Batteries
Battery
Clip
12
13. Make sure that all parts are properly tightened before you use the exercise cycle. Note: Some hard-
ware may be left over after assembly is completed.