Filter
Top Products
3 Clean the protective goggles with a moist cloth.
Storage
Let the appliance cool down for 15 minutes before you put it in transport position and store it.
1 Store the protective goggles in the storage compartment between the two lamps. (Fig. 38)
2 Put the remote control and the cord in the pouch on the back of the control panel (HB947 only). (Fig. 39)
3 Make sure the cord does not get stuck between parts of the appliance when you put the appliance in transport position.
4 Turn the appliance away from the bed or sofa and make sure there is enough space around the appliance to collapse it.
5 Press the two release buttons in the recesses of the control panel and slide the control panel down the stand as far as it goes. (Fig. 40)
6 Turn the lamp unit in the direction of the arrow. (Fig. 41)
You hear a click when the lamp unit locks in vertical position.
7 Pull the stand slightly backwards and then press the dual push button. Lower the stand slowly until the lamp unit rests on the oor
between the legs. (Fig. 42)
8 Wind the cord and fasten it with the Velcro cord wrap strip. (Fig. 43)
You can store the appliance in a wardrobe or under a bed.
Replacement
Have the Philips tanning lamps (Cleo HPA Synergy) replaced by a service centre authorised by Philips. Only they have the knowledge and
skills required for this job and the original spare parts for the appliance.
The light that the tanning lamps emit becomes less bright in time (i.e. after a few years in case of normal use). When this happens, you notice a
decrease in the tanning capacity of the appliance.
After 750 operating hours the tanning capacity of the lamps has decreased so much that replacement of the tanning lamps is advisable.
HB947/HB945: the appliance has a counter that records the operating hours of the tanning lamps. After 750 operating hours, an L appears
on the left-hand side of the display to indicate that replacement of the tanning lamps is advisable (Fig. 44).
Note:Of course, you can choose to postpone replacement for a while by setting a longer tanning time.
1 Set the time to 00 and press the repeat button ( ä) at least 2 seconds to make the operating hours appear on the display.
The maximum number of hours that can be displayed is 999. When this value has been reached, the counter starts to count up from
000 again.
Note:The operating hours disappear from the display as soon as you release the repeat button (
ä).
To remove the L from the display:
1 Make sure time indicated on the display is 00.
2 Press and hold down the START/STOP button.
3 Press and release the repeat button ( ä).
4 Press and release the pause button ( ã).
5 Press and release the repeat button ( ä).
6 Press and release the repeat button ( ä).
7 Release the START/STOP button (Fig. 45).
The L disappears from the display.
Have the Philips infrared lamps (1100W) and the UV lters replaced by a service centre authorised by Philips. Only they have the
knowledge and skills required for this job and the original spare parts for the appliance.
Have the infrared lamps replaced when they stop functioning.
The UV lters protect against exposure to undesired UV light. It is therefore important to have a damaged or broken lter replaced right
away.
If the mains cord is damaged, it must be replaced by Philips, a service centre authorised by Philips or similarly qualied persons in order to
avoid a hazard.
Ordering scent granules
You can obtain scent rell packages with 3 sachets of scent granules under type number HB080 through www.philips.com/shop or from your
Innergize dealer.
Environment
The lamps of the appliance contain substances that can be harmful to the environment. When you discard the lamps, make sure they are
not thrown away with the normal household waste, but handed in at an ofcial collection point.
Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the environment (Fig. 46).
,
-
-
-
-
-
,
,
ENGLISH 9