Filter
Top Products
503
EXS00 PEG DEC ATTACHMENT A~5~.E_M.J:$LY-I~STR.UL’I’IO~NS
..... ~.I-~
(STEe #2)
¯ ¯
THE ~RU~IONS FOR ~EP ~2 ARk T0 BE USED’WITH D~G SHEET ~! OF
1.
Loosely ~cmble one (I) 3/8 DIA. X 1 IN. LG. BUSH~G PULLEY ~d 0n~ (1) CABLE
CL~ to ~e PULLEY FLAT on ~e WEIGHT STACK S~PORT BASE, (CON~ION PO~
#3), using one (1) 3/8 X 1-3/4 BOLT, one (1) 3/8 LOCK WASHE~ ~d one (1) 3/8 ~. (SEE
A).
2.
ASSEMBLE ~e SWIVEL PULLEY B~C~TS using (1) 3/8 DIA x 3/4 BOLT, (2) ~/16 WAS~,
(1) 3/8 WASHER ~d (1) 3/8 LOCK NUT. ~IGHTEN UNTIL LOC~D, THEN’BACK O~
TURN.) (SEE DETAIL
’
3.
LOOSELY a~ach m’o (2) 3/8 DIA. X 1 IN. LG. BUSHING PULLEYS Mto ~e PULLEY E’.~C~T.-
ASSEMBLY, using ~vo (2) 3/8 X 1-1~ BOLTS, four (4) CAP WAS~RS, ~o (2) 3/8 ~S
(4) CAPS. (SEE DETAIL "B")
NOTE:
BEFORE PROCEEDING WITH CABLE INSTALLATION, UNtiL CABLE, AND .REMO~
AS MUCH SPI~LING AS POSSIBLE.
4.
~oute the PEC DEC LOOP CABLE ASSEMBLY through th~ top halfof~e PULLEY B~kC~T
ASSEMBLY. and securely a~ach each CABLE END to cnch CAM on the LE~ and ~GHT PEC DEC
ARMS, using two (2) 3 ’l 6 X 1 BOLTS, FOUR (4) ~/16 WASH ERS, ~vo (2) 5/16 LOCK WASHERS,
two (2) ~/16 NUTS.
NOTE
MAKE SURE CABLE ENDS ~EST FLAT AGAINST THE INSIDE OF THE CAMS) (SEE DETAIL
C AND PULLEY REFERENCE POINTS A, B, & C ON THE CABLE RO~ING-DIAG~M
VIE~V OF THE ASSEMBLED PRODUCT
NOTE:
POSITION THE CABLE RETAINING CLIPS O~ THE PULLEY B~CKET SUPPORT IN A
VERTICAL POSITION AFTER PEC DEC LOOP CABLE ASSEMBLY HAS BEEN ROUTED,
AND TIGHTEN SECURELY (SEE ASSEMBLY VIEW ON SHEET
SKIP SEOUENCE ~5 IF ASSEMBLING PEC DEC AND THE BASE U’NI~T THE
SA~IE TI~E.
5.
Disconnect the OLD SECONDARY CABLE ASSEMBLY at the LEG CURL ATTACHMENT
CONNECTION POINT #4 (SEE DETAIL D) and remove it by pulling it out from the LOW ROW
PULLEY STATION (CONNECTION POINT #5) and discard. Loosen the bolt connection
PULLEY REFERENCE POINT H so that the SECONDARY CABLE ASSEMBLIES (OLD & NEW
SWAPOUT) can be passed under the CABLE RETAINER CLIP.
5.
Reroute the new SECONDARY SWAPOUT CABLE ASSE.MBLY b.v starting at PULLEY reference
point D on the CABLE ROUTING DIAGRAM. Continue to pass the CABLE ASSEMBLY over
, PULLEYS REFERENCE POINTS E, F. G, & H, and reartach the CABLE end to the LEG CURL
EXTENSION CAM as shown in DETAIL D. (MAKE SURE CABLE END RESTS FLAT ON THE
CAM) Re ti,_,hten the [’,.~’.t connections at PULLEY REFERENCE POINTS H (ADJUSTABI’.E PRE
..... STRE~ECH~LI ELEI-~-’- F..~-P U LLEY FLA:I’.na. the-WEt.G HI.~TACK .SUPPORT- BASE-).
TIGHTEN all PULLEY CONNECTIONS.