Filter
Top Products
10
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
11
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
A S S E M B LY S T E P 3
BOLT (F)
SPRING WASHER (C)
FLAT WASHER (D)
CONSOLE
CONSOLE CABLE
DO NOT ATTACH
THIS SIDE UNTIL STEP 3-D
LEFT CONSOLE MAST
BOLT (F)
25 mm
Qty: 4
SPRING WASHER (C)
15 mm
Qty: 4
FLAT WASHER (D)
15 mm
Qty: 4
HARDWARE BAG 3 CONTENTS :
A Open HARDWARE BAG 3.
B With running deck in lowered position, place CONSOLE on the console masts. Align the
brackets that are underneath the console with the top holes of the console masts.
C To assemble the CONSOLE to the LEFT CONSOLE MAST, insert 1 BOLT (F),
1 SPRING WASHER (C) and 1 FLAT WASHER (D) into the 2 holes in the
LEFT CONSOLE MAST and lightly tighten.
D Locate CONSOLE CABLE COVER on back of CONSOLE and remove.
E Attach CONSOLE CABLE to CONSOLE BOARD. NOTE: Do not pinch CONSOLE CABLE.
F Replace CONSOLE CABLE COVER on back of CONSOLE and attach excess wire to CABLE TIE.
G Repeat STEP C above to assemble the RIGHT CONSOLE MAST to the CONSOLE.
A S S E M B LY S T E P 4
SCREWS (I)
DECK
LOCK
LATCH
LEFT HANDLEBAR
Open HARDWARE BAG 4.
Attach DECK LOCK LATCH to LEFT HANDLEBAR using 2 SCREWS (I).
Slide the WATER BOTTLE HOLDER down into the hole in the CONSOLE and snap together.
A
B
C
NOTE: Do not completely tighten any screws or bolts until step 5 is complete!
SCREW (I)
15 mm
Qty: 2
HARDWARE BAG 4 CONTENTS :
WATER BOTTLE
HOLDER
A S S E M B LY S T E P 3 ( C O N T I N U E D )
ATTENTION! Please note assembly changes to User’s Guide.
CONSOLE CABLE COVER
CABLE TIE
CONSOLE CABLE COVER
CABLE TIE
CONSOLE
BOARD
CONSOLE
CABLE
D Locate CONSOLE CABLE COVER on
back of CONSOLE and remove.
E Attach CONSOLE CABLE to
CONSOLE BOARD. NOTE: Do not
pinch CONSOLE CABLE.
F Replace CONSOLE CABLE COVER on
back of CONSOLE and attach excess
wire to CABLE TIE.
ASSEMBLY STEP 3
NOTE: Assembly step D modified to reflect proper CONSOLE CABLE connection to CONSOLE.
ATTENTION! Please note assembly changes to User’s Guide.
CONSOLE CABLE COVER
CABLE TIE
CONSOLE CABLE COVER
CABLE TIE
CONSOLE
BOARD
CONSOLE
CABLE
D Locate CONSOLE CABLE COVER on
back of CONSOLE and remove.
E Attach CONSOLE CABLE to
CONSOLE BOARD. NOTE: Do not
pinch CONSOLE CABLE.
F Replace CONSOLE CABLE COVER on
back of CONSOLE and attach excess
wire to CABLE TIE.
ASSEMBLY STEP 3
NOTE: Assembly step D modified to reflect proper CONSOLE CABLE connection to CONSOLE.
ATTENTION! Please note assembly changes to User’s Guide.
CONSOLE CABLE COVER
CABLE TIE
CONSOLE CABLE COVER
CABLE TIE
CONSOLE
BOARD
CONSOLE
CABLE
D Locate CONSOLE CABLE COVER on
back of CONSOLE and remove.
E Attach CONSOLE CABLE to
CONSOLE BOARD. NOTE: Do not
pinch CONSOLE CABLE.
F Replace CONSOLE CABLE COVER on
back of CONSOLE and attach excess
wire to CABLE TIE.
ASSEMBLY STEP 3
NOTE: Assembly step D modified to reflect proper CONSOLE CABLE connection to CONSOLE.
STEP D STEP E
STEP F
T90_Rev.1.5.indd 10-11 9/10/08 4:21:04 PM