Filter
Top Products
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
TREADMILL
OPERATION
LIMITED
WARRANTY
21
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
W I R E L E S S PE D O M E T E R IN S T R U C T I O N S
C U S T O M I Z I N G TH E SE T T I N G S
• TO ENTER SETTINGS MODE: While the display shows Step Count, press and hold and for 3 seconds.
• TO SCROLL THROUGH MODES: Press to advance a mode and to go back a mode.
• TO ENTER MODE: Press and hold for 3 seconds to enter a chosen mode.
• TO SCROLL THROUGH OPTIONS: Press to advance a setting and to go back a setting.
• TO SAVE OPTION: Press and hold for 3 seconds to save setting and exit mode.
• TO EXIT OPTION (WITHOUT SAVING): Press and hold for 3 seconds to exit the mode without saving changes.
• TO EXIT SETTINGS MODE: Press and hold for 3 seconds.
P-4: SLEEP MODE - The display back light will
automatically turn off if there is no activity for 30
seconds. The pedometer’s default setting should
not be adjusted as it is preset for optimal battery
longevity.
P-5: SENSITIVITY SETTING - There are three
sensitivity settings to choose from. Use the following
guide to customize your sensitivity needs:
• L1 = Low for heavy running/walking
• L2 = Medium for light jogging or medium walking
(default)
• L3 = High for light walking
P-0: SOFTWARE VERSION - Cannot be changed.
P-1: DISPLAY BRIGHTNESS - There are eight brightness
settings to choose from.
P-2: STEP COUNT UPDATE (STEPS) - Adjusts how often
(in steps) the pedometer will transmit to the treadmill.
The pedometer’s default setting should not be adjusted
as it is preset for optimal battery longevity.
P-3: STEP COUNT UPDATE (SECONDS) - Adjusts how
often (in seconds) the pedometer will transmit to the
treadmill. The pedometer’s default setting should no be
adjusted as it is preset for optimal battery longevity.
BATTERY REPLACEMENT
The battery in your pedometer can be expected to last six
months for someone who walks 10,000 steps per day. Results
may vary depending on usage. Your pedometer uses one (1)
Lithium CR1225 battery. Should your display become faint or the
transmitter signal only picks up at a very short distance, it may
be time to replace the battery.
Note: Battery replacement is the responsibility of the customer
and is not covered under Horizon Fitness’ Limited Home Use
Warranty.
NO DISPLAY
• The LCD display is designed to be used in temperatures
between 32 to 104 degrees Fahrenheit (0-40 degrees
Centigrade). If the pedometer is being used outside of this
range, return to room temperature to restore operation.
• Avoid placing the LCD in direct sunlight for long periods of
time. Return to room temperature to restore operation.
• The pedometer may be in Sleep Mode. Press the SEND button
to turn on pedometer.
• The battery needs to be replaced. Your pedometer uses one (1)
Lithium CR1225 battery.
T R O U B L E S H O O T I N G PE D O M E T E R
ERRATIC OR INCONSISTENT DISPLAY
• The pedometer may not be positioned correctly on your body.
See ‘Positioning Pedometer’ in Section 1 for details.
• The battery needs to be replaced. Your pedometer uses one
(1) Lithium CR1225 battery.
• If the treadmill display is erratic: Check your exercise
environment for sources of interference such as fluorescent
lights, computers, underground fencing, home security
systems or appliances containing large motors. These items
may cause interference between the pedometer and the
receiver on the treadmill.
INACCURATE STEP COUNT
• For the most accurate step count readings, you must walk at
a speed over 2.0 mph. The average walking speed is 2-4 mph.
• If you believe your step count is innacurate, do the following:
Walk and count 100 steps. Compare your count to the
pedometer’s. If the pedometer’s count is less than yours,
increase the sensitivity setting. If the pedometer’s count
is more than yours, decrease the sensitivity setting. (See
Settings, P-5 to change the sensitivity setting.)