Horizon Fitness CX-66 Elliptical Trainer User Manual


  Open as PDF
of 21
 
BEFORE
YOU BEGIN
10
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
BEFORE
YOU BEGIN
ASSEMBLY
11
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY STEP 4
SCREW (J)
PEDAL ARM COVER
PEDAL ARM
ROLLER WHEEL COVER
SCREW (K)
SCREW (J)
15 mm
Qty: 2
SCREW (K)
12 mm
Qty: 2
HARDWARE BAG FOR STEP 4 CONTENTS :
ASSEMBLY STEP 5
CONSOLE MAST
LOWER HANDLEBAR
PRE-ATTACHED
BOLT & WASHER
UPPER HANDLEBAR
PRE-ATTACHED
SET SCREWS
NOTCH
TAB
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
CONSOLE MAST
PRE-ATTACHED BOLTS AND WASHERS
UPPER HANDLEBAR
PRE-ATTACHED SCREWS
LOWER HANDLEBAR
NOTE: There is NO hardware bag for this step. All hardware is pre-attached.
A) Remove PRE-ATTACHED BOLTS and WASHERS from CONSOLE MAST.
B) Slide right LOWER HANDLEBAR on CONSOLE MAST and attach by reinserting PRE-ATTACHED BOLT and WASHERS.
C) Remove PRE-ATTACHED SET SCREWS from right UPPER HANDLEBAR
D) Slide right UPPER HANDLEBAR onto LOWER HANDLEBAR and secure by reinserting PRE-ATTACHED SET SCREWS
E) Repeat on other side.
After handlebars are assembled they will rotate freely – be cautious. Until the
machine is fully assembled, do not grab the handlebars for support.
CONSOLE MAST
LOWER HANDLEBAR
PRE-ATTACHED
BOLT & WASHER
UPPER HANDLEBAR
PRE-ATTACHED
SET SCREWS
NOTCH
TAB
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
CONSOLE MAST
PRE-ATTACHED BOLTS AND WASHERS
UPPER HANDLEBAR
PRE-ATTACHED SCREWS
LOWER HANDLEBAR
A) Open HARDWARE BAG FOR STEP 4.
B) Attach the PEDAL ARM COVER using 1 SCREW (J).
C) Attach the ROLLER WHEEL COVER using 1 SCREW (K).
D) Repeat on other side.
CX-66_Elliptical_Rev.1.6.indd 10-11 6/13/07 1:26:28 PM
 previous next