Filter
Top Products
BEFORE
YOU BEGIN
8
INTRODUCTION
IMPORTANT
PRECAUTIONS
ASSEMBLY
BEFORE
YOU BEGIN
ELLIPTICAL
OPERATION
LIMITED
WARRANTY
TROUBLESHOOTING
& MAINTENANCE
CONDITIONING
GUIDELINES
BEFORE
YOU BEGIN
ASSEMBLY
9
INTRODUCTION
IMPORTANT
PRECAUTIONS
ELLIPTICAL
OPERATION
CONDITIONING
GUIDELINES
TROUBLESHOOTING
& MAINTENANCE
LIMITED
WARRANTY
ASSEMBLY STEP 2
MAIN FRAME
CONSOLE WIRES
CONSOLE MAST
BOLT (A)
SPRING WASHER (B)
FLAT WASHER (C)
CONSOLE
MAST
BOOT
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
MID-STABILIZER COVER
FLAT WASHER (E)
MID-STABILIZER
BOLT (D)
REAR STABILIZER CAPS
STABILIZER BAR
A) Open HARDWARE BAG FOR STEP 2.
B)
Carefully slide the STABILIZER BAR through the MID-STABILIZER.
C)
Attach MID-STABILIZER COVERS to the STABILIZER BAR using 2 BOLTS (D) and 2 FLAT WASHERS (E).
D)
Slide REAR STABILIZER CAPS into the REAR STABILIZER
to seal the rear stabilizer holes
.
BOLT (D)
19 mm
Qty: 2
FLAT WASHER (E)
16 mm
Qty: 2
HARDWARE BAG FOR STEP 2 CONTENTS :
MAIN FRAME
CONSOLE
MAST
BOOT
TOP BACK COVER
SCREWS (K)
TOP SIDE COVERS
(EX-65, EX-75)
ACCESSORY TRAY
(EX-65, EX-75)
TOP FRONT COVER
EX-55 ONLY
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
SCREWS (F)
FOOTPAD
BOLT (G)WASHER (H)
WAVY WASHER (D)
WASHER (H)
MAIN FRAME
PEDAL ARM
BOLT (G)WASHER (I)WASHER (H)
ASSEMBLY STEP 3
MAIN FRAME
CONSOLE
MAST
BOOT
TOP BACK COVER
SCREWS (K)
TOP SIDE COVERS
(EX-65, EX-75)
ACCESSORY TRAY
(EX-65, EX-75)
TOP FRONT COVER
EX-55 ONLY
Quantity
2
Picture
2
2
List
Z24. Wave Washer
Z02. M8X19L Bolt
Z01. 16mm FLat Washer
2Z07. Plain Washer
2
6
6
4
8
2
2
2
2
2
2
8
6
2
Z03. Spring Washer
Z04. M8x15mm Bolt
Z25. Plain Washer
Z08. Plain Washer
Z12. 44mm Axis
Z13. M8 Nylon Nut
Z14. 60mm Bolt
Z17. M5X12L Screw
Z16. M4X15L Screw
Z30. M4x12L Bolt
Z05. M8x13mm Bolt
Z09. 15.9mm Teflon Washer
Z06. Wave Washer
Z10. M4X15L Screw
SCREWS (F)
FOOTPAD
BOLT (G)WASHER (H)
WAVY WASHER (D)
WASHER (H)
MAIN FRAME
PEDAL ARM
BOLT (G)WASHER (I)WASHER (H)
A) Open HARDWARE BAG FOR STEP 3.
B) Attach FOOTPAD to PEDAL ARM using 4 SCREWS (F).
C) Attach PEDAL ARM to the MAIN FRAME with 1 BOLT (G
)
, 1
WASHER (I),
1
WAVY WASHER (D)
and 1
WASHER (H).
D) Repeat on other side.
SCREW (F)
12 mm
Qty: 8
BOLT (G)
13 mm
Qty: 2
WASHER (H)
Qty: 2
WASHER (I)
Qty: 2
WAVY WASHER (D)
Qty: 2
angle view
HARDWARE BAG FOR STEP 3 CONTENTS :
CX-66_Elliptical_Rev.1.6.indd 8-9 6/13/07 1:26:14 PM