Elite BK2080 Bicycle User Manual


  Open as PDF
of 7
 
Owner’s Manual
3
Owner’s Manual
2
IMPORTANT SAFETY NOTICE
Note the following precaution before assembling or operating the machine.
1. THE MAXIMUM WEIGHT CAPACITY OF THE ORBITREK ELITE IS 275 LBS (125 kgs).
Persons whose body weight exceeds this limit should NOT use this machine.
2. Keep children and pets away from the Orbitrek Elite at all times. DO NOT leave
unattended children in the same room with the machine.
3. Handicapped or disabled persons should not use the Orbitrek Elite without the presence
of a qualified health professional of a qualified health professional or physician.
4. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
5. Before beginning training, remove all within a radius of 2 meters from the machine.
DO NOT place any sharp objects around the Orbitrek Elite.
6. Position the Orbitrek Elite on a clear, level surface away from water and moisture.
Place mat under the unit to help keep the machine stable and to protect flooring.
7. Use the Orbitrek Elite only for its intended use as described in this manual.
DO NOT use any other accessories not recommended by the manufacturer.
8. Assemble the machine exactly as the descriptions in the instruction manual.
9. Check all bolts and other connections before using the machine for the first time and
ensure that the trainer is in the safe condition.
10. Hold a routine inspection of the equipment.Pay special attention to components which
are the most susceptible to wear off, i.e.connecting points and wheels. The defective
components should be replaced immediately. The safety level of this equipment can only
be maintained by doing so. Please don't use the Orbitrek Elite until it is repaired well.
11. NEVER operate the Orbitrek Elite if it is not functioning properly.
12. This machine can be used for only one person’s training at a time.
13. Do not use abrasive cleaning articles to clean the machine. Remove drops of sweat
from the machine immediately after finishing training.
14. Always wear appropriate workout clothing when exercising. Running or aerobic shoes
are also required.
15. Before exercising, always do stretching first.
16. The power of the machine increases with increasing the speed, and the reverse.
The machine is equipped with adjustable knob, which can adjust the resistance.
WARNING: BEFORE BEGINNING THIS OR ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN
F I R S T. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH
PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING THE ORBITREK ELITE.
THANE ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTA I N E D
BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS
BEFORE you begin:
1. Locate a comfortable work site. Assemble your OrbiTrek Elite in an open space with adequate
ventilation and lighting. Because the OrbiTrek Elite is portable, to some extent, you need not
assemble it exactly where it is to be used. For your convenience, however, you should avoid
hauling the machine across excessive distances, through narrow passage ways or over staircases
once its assembly is complete.
2. It’s a good idea to flatten out the shipping carton, and use it as a work surface when you
assemble the OrbiTrek Elite. Keep a few paper towels handy since some of the components
are lightly pre-greased.
Notice:
Find your tools. You will need the following tools to assemble the Orbitrek Elite.
Ruler with both metric and English measurements
Allen wrench (6# and 8#)
Spanner
Before assembling please check whether all needed parts are available (at the above of this instruction
sheet you will you will find an exploded drawing with all single parts (marked with numbers) which this
item consist of.
Identify your hardware:
Organize your bolts and nuts before assembly. Nuts are identified by the diameter of the cavities.
For more information, refer to exploded view diagram and parts list on pages 8-10 of this manual.
ASSEMBLY INSTRUCTIONS
NO.1 LEFT HINGE BOLT
NO.6 SPRING
WASHER (1/2”)
NO.7 LEFT LOCK NUT (1/2”)
NO.9 CARRIAGE BOLT (M8*60)
NO.11 ARC WASHER (Ø8) NO.12 DOMED NUT (M8)
NO.13 NUT (M8)
NO.14 FLAT WASHER (Ø8)
NO.20 BOLT (M8*45)
NO.31 HINGE SCREW (3/8”*20)
NO.32 SPRING
WASHER ( 10)
NO. 33 D SHAPER WASHER
NO.93 ARC WASHER
(dl=16 D=26 s=0.3)
NO.34 LOCKING
KNOB
NO.38 SPINDLE BAR NO.89 RIGHT LOCK NUT (1/2”)
NO.42 RIGHT HINGE BOLT
ALLEN WRENCH 8#
ALLEN WRENCH 6#
SPANNER
 previous next