Filter
Top Products
Using the Timer
This page should be read with the watch diagram, on
the first page of this manual, showing the location of
the parts.
The timer can be set from 1 to 60 minutes in
increments of 1 minute.
[Preparation for using the timer]
1. Press the ࠗ
M (MODE) button to move the
mode hand to [TMR].
2. Pull the ࠗ
M (MODE) button out to the
setting position.
3. Use the ࠗ
C (SET) button to set the time for the timer.
4. Push the ࠗ
M (MODE) button in to its normal
position. Now timer setting is completed.
[Using the timer - 1]
1. Pressing the ࠗ
A (START) button starts
the countdown. (When the set time
has expired (time up), the watch beeps
for 5 seconds.)
2. Pressing the ࠗ
A (STOP) button stops the countdown.
3. Pressing the ࠗ
C (RESET) button resets the timer
back to the set time.
[Using the timer - 2]
1. Pressing the ࠗ
M (MODE) button starts the
countdown.
2. Pressing the ࠗ
C button resets the timer back to the
set time and restarts the countdown again. (This
function is useful in restarting the countdown quickly.)
3. Pressing the ࠗ
A (STOP) button stops the countdown.
4. Pressing the ࠗ
C (RESET) button resets the timer
back to the set time.
Convenient Functions
This page should be read with the watch diagram, on
the first page of this manual, showing the location of
the parts.
Ⅵ When the hands of the analog section cover
the digital section, making the time in digital
difficult to read, utilise the –
Hand-retractor function:
Use this function to retract the hour and minute hands
of the analog section to the 12 o’clock position.
[Operation]
Hold the ࠗ
B button down for 2 seconds and then
release it when “H.R” blinks in [10].
*During Hand-Retractor mode the minute hand of
the UTC time at [3] goes back and forth by 1 minute
(-1 minute
ᮤ ᮣ +1 minute), and “H.R” displayed
at [10] blinks.
[Cancelling Hand-Retractor mode]
Pressing the ࠗ
B button again cancels Hand-
Retractor mode.
(H.R.: Abbreviation of Hand-Retractor)
Ⅵ When the watch displays something
improperly and a malfunction is suspected,
perform –
ALL RESET and zero positioning:
When the watch displays something improperly
and a malfunction is suspected, perform ALL RESET
and zero positioning, then readjust the time,
calendar and other modes.
[ALL RESET]
This function can be operated from any mode.
1. Pull the ࠗ
M (MODE) button out to the setting
position.
2. Hold down the ࠗ
A , ࠗB and ࠗC buttons
simultaneously for more than 2 seconds then
release them.
(All digital segments will light up. Immediately
reset to the zero position.)
[Zero positioning]
1. Pressing the ࠗ
B button resets all segments in
the digital section to zeros.
2. The digital display changes in the sequence of
UTC ➡ HR ➡ MIN each time the ࠗ
B button is
pressed.
UTC: For zero positioning of the UTC time display
HR: For zero positioning of the hour hand and
24-hour hand
MIN: For zero positioning of the minute hand.
3. Pressing the ࠗ
A (UP) button turns each hand
clockwise. Pressing the ࠗ
C (DOWN) button
turns each hand counterclockwise. Align all
hands to the 12 o’clock position.
4. When the ࠗ
M (MODE) button is pushed in to its
normal position, the watch beeps and at the
same time the hands start moving. ALL RESET
and zero positioning are now completed.
5. Set the time, calendar and other modes.