Filter
Top Products
Operation Guide 4782 (OC)
7
About the Display
Elapsed Time Screen
A 1/100 second value is displayed for the first minute after you start
an elapsed time measurement. After the first minute, the screen
changes automatically to show elapsed minutes and seconds.
Second
1/100 second
Seconds, 1/100-second Screen
Minute
Second
Minutes, Seconds Screen
Paused Elapsed Time Measurement Screen
When elapsed time measurement is paused, the display alternates
between a minute/second screen and a 1/100 second screen at one-
second intervals.
Minute
Second
1/100 second
The stopwatch measures elapsed time in units of 1/100 second up to
99 minutes, 59.99 seconds (100 minutes). When the maximum limit
is reached, the elapsed time returns to zero automatically and timing
continues from there.
❚
To start or stop an elapsed time
operation
In the Stopwatch Mode, press the
DD
DD
D button to start and stop
the stopwatch.
• Each press of the D button starts or stops the stopwatch.
(Split/Reset)
(Start/Stop)
Use the
CC
CC
C
button to enter the Stopwatch Mode as shown
under “Modes and Indicators”.
❚
To measure elapsed time
Start Stop Reset
Pressing the A button while timing is stopped resets the stopwatch
to all zeros.
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting it to
all zeros will resume elapsed time measurement from where it was
last stopped.
❚
To measure split times
Start Record Split Release Split Stop Reset
Pressing A while timing is being performed freezes the current
elapsed time on the display, but timing of the next split continues
internally.
• Changing to another mode while a split time is displayed cancels
the split time operation.
❚
To time 1st and 2nd place finishers
Start 1st Finisher
(Displays time
of 1st finisher.)
2nd Finisher Displays time
of 2nd finisher.
Reset
Pressing the D button while the split time screen is on the display
stops elapsed time measurement, leaving the split time screen on
the display. Press the A button to exit the split time screen and
display the elapsed time when measurement was stopped.
Split Indicator
1/100 second
Minute Second
Split Time Indicator
The split time screen cycles alternately through the split
indicator, a minute/second screen, and a 1/100 second
screen.
Using the Stopwatch
Configuring Home City Settings
You can use the following procedure to set the current time and date
of the Home City that you have selected in the Timekeeping Mode.
• Always use the Timekeeping Mode to set and adjust the current
time and date settings.
• You also can turn Power Saving on and off while setting the time
and date.
If you are planning to adjust both the digital and analog
settings manually, be sure to adjust the digital setting first.
❚
To configure Home City settings
1. In the Timekeeping Mode
hold down the
AA
AA
A button
for about two seconds
until the currently selected
city code flashes on the
display.
• The second hand will move to
12 o’clock.
2. Use the
DD
DD
D (Eastward) and
BB
BB
B (Westward) buttons to
scroll through the city
codes until the one you
want to use as your Home
City is displayed.
• Display the time zone that you
want to select as your Home
Time Zone.
• See “World Time City Code
List” for a complete list of
city codes.
• Holding down either button
changes the setting at high
speed.
3. Press the
CC
CC
C button to
display the summer time
setting.
City Code
TYO = Tokyo
(Eastward)
(Westward)
4. Press the
DD
DD
D button to
cycle through the summer
time settings until the one
you want is displayed.
A (AUTO)
This setting enables the auto summer time setting, which
turns summer time on or off in accordance with the received
time calibration signal.
OF (OFF)
This setting turns off summer time, and displays the current
time normally.
ON
This setting turns on summer time. Selecting this setting
displays the DST indicator, and advances the current time
setting by one hour.
• Note that the above setting is used to turn summer time “OFF” or
“ON” manually when any city code other than those listed under
“Reception Ranges” is selected as the Home City.
5. Use the
CC
CC
C button to cycle
through the settings
shown below.
• Each press of C causes the
applicable setting to flash.
Summer TimeHome City
Power Saving
Language
12/24-hour
Timekeeping
Hour
MinuteMonth YearDay
Second