Filter
Top Products
Operation Guide 5262
L-1
City Code Table
E-77
Stopwatch: Measuring capacity: 23'59.99"
Measuring unit: 1/100 second
Measuring mode: Elapsed time, split time
World Time: 29 cities (29 time zones) and Coordinated Universal Time
Other: Standard Time/Daylight Saving Time (summer time); Home City/World Time
City swapping
Alarm: Daily alarm
Other: Power Saving; Low battery alert; Auto Correction of Hand Home Positions
Power Supply: Solar panel and one rechargeable battery
Approximate battery operating time: 5 months (no exposure to light after a full
charge; 10 seconds alarm beeper operation, analog hands operational 18 hours per
day and one signal reception of approximately 4 minutes per day)
E-76
Specifi cations
Accuracy at normal temperature: ±15 seconds a month (with no signal calibration)
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, 24-hour,
day, day of the week
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 29 city codes and Coordinated
Universal Time); Daylight Saving Time (summer time) / Standard Time
Time Calibration Signal Reception: Auto receive up to six times a day (5 times a
day for the Chinese calibration signal; Remaining auto receives
cancelled as soon as one is successful); Manual receive
Receivable Time Calibration Signals:
Mainfl ingen, Germany (Call Sign: DCF77, Frequency: 77.5 kHz);
Anthorn, England (Call Sign: MSF, Frequency: 60.0 kHz); Fukushima,
Japan (Call Sign: JJY, Frequency: 40.0 kHz); Fukuoka/Saga, Japan
(Call Sign: JJY, Frequency: 60.0 kHz); Fort Collins, Colorado, the
United States (Call Sign: WWVB, Frequency: 60.0 kHz); Shangqiu City,
Henan Province, China (Call Sign: BPC, Frequency: 68.5 kHz)
E-75
■ Signal reception is being performed successfully, but the time and/or day is
wrong.
Possible Cause Remedy Page
Your Home City setting is wrong.
Check your Home City setting and correct it,
if necessary.
E-33
The watch may have been
exposed to magnetism or strong
impact, which has caused
problems with proper hand and
day alignment.
Adjust the watch’s hand and day home
positions.
E-62
E-74
■ Auto Receive is not performed or I cannot perform Manual Receive.
Possible Cause Remedy Page
The watch is in the Stopwatch
Mode.
Auto Receive is not performed while the watch
is in the Stopwatch Mode. Hold down C at
least two seconds to enter the Timekeeping
Mode.
E-30
Your Home City setting is wrong.
Check your Home City setting and correct it,
if necessary.
E-33
There is not enough power for
signal reception.
Expose the watch to light to charge it. E-9
E-73
■ The current time setting changes after I set it manually.
You may have the watch confi gured for Auto Receive of the time calibration signal
(page E-24), which will cause the time to be adjusted automatically according to your
currently selected Home City. If this results in the wrong time setting, check your
Home City setting and correct it, if necessary (page E-33).
■ The current time setting is off by one hour.
Possible Cause Remedy Page
Signal reception on a day for
switching between STD (standard
time)/DST (daylight saving/
summer time) may have failed for
some reason.
Perform the operation under “To get ready
for a receive operation”. The time setting will
be adjusted automatically as soon as signal
reception is successful.
E-22
If you are unable to receive the time calibration
signal, change the STD (standard time)/DST
(daylight saving/summer time) setting manually.
E-36
E-72
■ The
x
Second Hand indicates NO (N) when I check the result of the latest
receive operation.
Possible Cause Remedy Page
You are wearing or moving the x
watch, or performing a button
operation during the signal
receive operation.
The watch is in an area with x
poor reception conditions.
Keep the watch in an area where reception
conditions are good while the signal receive
operation is being performed.
E-22
You are in an area where signal
reception is not possible for some
reason.
See “Approximate Reception Ranges”. E-19
The calibration signal is not being
transmitted for some reason.
Check the website of the organization that x
maintains the time calibration signal in your
area for information about its down times.
Try again later. x
—
E-71
Charging
■ The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3 (page E-11). Continue
exposing the watch to light until the
x
Second Hand starts moving normally (at one-
second intervals).
■ The
x
Second Hand starts to move at one-second intervals, but then suddenly
returns to moving at two-second intervals.
The watch probably is not suffi ciently charged yet. Continue keeping it exposed to
light.
Time Calibration Signal
The information in this section applies only when LON, PAR, ATH, HNL, ANC, LAX,
DEN, CHI, NYC, HKG, or TYO is selected as the Home City. You need to adjust the
current time manually when any other city is selected as the Home City.
E-70
World Time Mode
■ The World Time indicated by the
n
Right Dial Hands in the World Time Mode is
one hour off from the actual time in the selected World Time City.
The STD (standard time)/DST (daylight saving/summer time) setting of the selected
World Time City may be wrong. Select the correct STD (standard time)/DST (daylight
saving/summer time) setting (page E-53).
■ The World Time indicated by the
n
Right Dial Hands in the World Time Mode
is off.
Your Home City settings may be wrong. Check your Home City settings and correct
them, if necessary (page E-33).