Filter
Top Products
Operation Guide 5262
E-69
■ The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is
possible, see “To confi gure Home City settings” (page E-33).
If you are using the watch in an area where time calibration signal reception is not
possible, you may need to change your Home City’s STD (standard time)/DST
(daylight saving/summer time) setting manually. Use the procedure under “To toggle
the Home City time between standard time and daylight saving time” (page E-36) to
change the STD/DST setting.
■ The hands and/or day indicator is off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day alignment. Adjust the watch’s
hand and day home position alignment (page E-62).
E-68
The time setting is being adjusted following a successful auto time calibration x
signal receive operation (page E-17).
The watch is returning to the Timekeeping Mode automatically from the Alarm Mode x
(page E-58).
■ Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-13). Do not perform any
operation until the hands return to their normal positions (in about 15 minutes). The
hands should return to their correct positions when normal operation returns. To help
power recover, leave the watch in a location where it is exposed to light.
The current time setting is off by hours.■
Your Home City setting may be wrong. Check your Home City setting and correct it, if
necessary (page E-33).
E-67
Troubleshooting
Hand Movement and Position
■ I lost track of what mode the watch is in.
Refer to “To select a mode” (page E-31). To return directly to the Timekeeping Mode
from any other mode, hold down C at least two seconds.
■ The
x
Second Hand is moving at two-second intervals.
■ All the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the
x
Second Hand starts moving
normally, at one-second intervals (page E-11).
■ The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
The watch is recovering from a sleep state (page E-15).
x
E-66
After confi rming that the 5.
n
Right Dial Hands are in the
correct home position, press C. This will advance to
v
Left Dial Hand home position adjustment.
The
x
v
Left Dial Hand is in the correct home position if
it is pointing at 12 o’clock. If it isn’t, use D (+) and B
(–) to move it to 12 o’clock.
After confi rming that the 6.
v
Left Dial Hand is in the
correct home position, press C. This will advance to
day home position adjustment.
The
x
m
Day Indicator is in the correct home position
if it shows 1. If the 1 is not in the center of the
m
Day
Indicator, use D (+) and B (–) to center it.
Press 7. A to return to the Timekeeping Mode.
The
x
m
Day Indicator moves to the current day, and then the
z
Hour Hand and
the
c
Minute Hand move to the current time. Wait until everything stops moving.
> 6
5
E-65
After confi rming that the 3.
x
Second Hand is at the proper
home position, press C. This will switch to
z
Hour
Hand and
c
Minute Hand home position adjustment.
The x
z
Hour Hand and
c
Minute Hand are at their
proper home positions if they both move to 12 o’clock.
The
b
24-hour Hand also will move along with
z
Hour Hand movement, and cannot be adjusted
individually. If the hands are not positioned correctly,
use D (+) and B (–) to move them to their proper
home positions.
After confi rming that the 4.
z
Hour Hand and
c
Minute
Hand are in their correct home positions, press C.
This will switch to
n
Right Dial Hand home position
adjustment.
The
x
n
Right Dial Hands are at their proper home positions if they both move
to 24. If the hands are not positioned correctly, use D (+) and B (–) to move
them to 24.
B +
* 6
@
E-64
Each press of x C in the home position adjustment mode will cycle through the
adjustment settings as shown below.
x
Second
z
Hour/
c
Minute/
b
24-hour
n
Right Dial Hands
v
Left Dial Hand
m
Day Indicator
C C
C
C
C
When adjusting a hand or the date home position, it is recommended that after x
you move to a proper home position, you press B to move the setting back one
step. Next, press D again to return it to the home position. This helps to ensure
better home position adjustment accuracy.
E-63
To adjust home positions manually
Hold down 1. C at least two seconds until the
x
Second
Hand stops and then starts moving again.
Hold down 2. D for about three seconds.
The
x
x
Second Hand will start to move when you fi rst
press D. Keep D depressed until the
x
Second
Hand stops.
The watch is now in the home position adjustment
x
mode.
The watch will exit the adjustment mode automatically x
if you do not perform any operation for about two or
three minutes.
First is
x
x
Second Hand home position adjustment.
If the
x
x
Second Hand moves to 12 o’clock, it is in the
correct home position. If it doesn’t, use D to move it
to 12 o’clock.
B +
* 6> 5
@
E-62
Adjusting Home Positions Manually
Strong magnetism or impact can cause the hands and/or day of the watch to be off,
even if the watch is able to perform the signal receive operation. If this happens,
perform the applicable home position adjustment procedures in this section.
Hand home position adjustment is not required if the time and day settings are
x
correct.
You also can use auto correction of the hand home positions (page E-59) to correct x
the home positions of the
z
Hour Hand,
c
Minute Hand, and
x
Second Hand.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in the home position adjustment mode. In either case,
any adjustments you made before the watch returned to the Timekeeping Mode will
be applied.
E-61
If you release x D when the
x
Second Hand stops the fi rst time (after about three
seconds) in the above operation, the watch will enter the home position adjustment
mode, which is described under “Adjusting Home Positions Manually” (page E-62).
If this happens, press A to return to the Timekeeping Mode and then perform the
above operation again.
Manually triggered auto correction of hand home positions performs the following
x
two steps.
The hands will move automatically in order to determine the home positions of the 1.
watch.
After the hand home positions are determined, the watch will return to normal 2.
timekeeping automatically. This completes the correction operation.
E-60
To trigger auto correction of hand home positions
Perform the following procedure when the time setting
x
is off.
In the Timekeeping Mode, hold down D for about six
seconds until the
x
Second Hand completes one full
revolution.
Though the
x
x
Second Hand will stop momentarily about
three seconds after you hold down D, do not release
the button yet. Wait until the
x
Second Hand completes
a full revolution before you release D.
To interrupt an ongoing correction operation and return
x
to the Timekeeping Mode, press D again.
@
B +