Filter
Top Products
Operation Guide 5114 5214
E-16
Approximate Reception Ranges
UK and German Signals
Anthorn
500 kilometers
1,500 kilometers
The Anthorn signal is
receivable within this area
Mainflingen
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
Fort Collins
North American Signal
Japanese Signals Chinese Signal
500 kilometers
Changchun
Beijing
Shangqiu
Shanghai
Chengdu
Hong Kong
1,500 kilometers
1,000 kilometers
Fukuoka/Saga
500 kilometers
Fukushima
E-17
• Even when the watch is within range of a transmitter, signal reception may be impossible due to the
effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,
etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the
infl uence of the conditions listed above becomes even greater.
• Signal reception may not be possible at the distances noted below during certain times of the year or
day. Radio interference may also cause problems with reception.
Mainfl ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 500 kilometers (310 miles)
• As of July 2010, China does not use Daylight Saving Time (DST). If China does go to the Daylight
Saving Time system in the future, some functions of this watch may no longer operate correctly.
• Using this watch in a country covered by a time calibration that is different from the countries it
supports may result in incorrect time indication due to local application of summer time, etc.
E-18
To get ready for a receive operation
1. Confi rm that the watch is in the Timekeeping Mode. If it isn't, hold down
D
for about two seconds to
enter the Timekeeping Mode. (page E-24)
2. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing
towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.
• Signal reception normally is better at night.
• The receive operation takes from two to seven minutes, but
in some cases it can take as long as 14 minutes. Take
care that you do not perform any button operation or
move the watch during this time.
12 o’clock
or
12 o’clock
or
E-19
• Signal reception may be diffi cult or even impossible under the conditions described below.
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
offi ce
equipment,
or a mobile
phone
Near a
construction
site, airport,
or other
sources of
electrical
noise
Near
high-tension
power lines
Among or
behind
mountains
3. What you should do next depends on whether you are using Auto Receive or Manual Receive.
• Auto Receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”
below for details.
• Manual Receive: Perform the operation under “To perform manual receive” on page E-20.
Auto Receive
• With Auto Receive, the watch performs the receive operation each day automatically up to six times (up
to fi ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to
the Timekeeping Mode time). When any receive operation is successful, none of the other receive
operations for that day are performed.
• When a calibration time is reached, the watch will perform the receive operation only if it is in the
Timekeeping Mode or World Time Mode. The receive operation is not performed if a calibration time is
reached while you are confi guring settings.
E-20
• You can use the procedure under “To turn auto receive on and off” (page E-21) to enable or disable
auto receive.
To perform manual receive
1. Use
D
to select the Receive Mode (
RC
) as shown on page E-24.
2. Hold down
A
until the second hand points to
READY
(or
R
on some
models).
• This indicates that the watch is ready for signal reception.
• After a short while, the second hand will move to WORK (or W on
some models) and signal reception will begin. Do not operate
any of the watch’s buttons until the second hand starts moving
normally again, which indicates that reception is complete.
• If signal reception is unstable, the second hand may keep moving
between WORK ( W) and READY ( R).
• OK will appear on the digital display if the receive operation is
successful, while Err indicates reception was unsuccessful.
• If the second hand remains at READY ( R), press any button to cancel
signal reception. Move the watch to a location where reception
conditions are better and try again.
3. Press
D
twice to return to the Timekeeping Mode.
Note
To cancel an ongoing signal receive operation, press any of the watch’s
buttons. This will return to the Receive Mode screen in step 1 of this
procedure.
Receiving
Receive successful
Second
hand
Receiving
Receive successful
Second
hand
Receive failedReceive failed
E-21
To check the latest signal reception results
Enter the Receive Mode (page E-24).
• When receive is successful, the digital display shows the time and
date that receive was successful.
- : - -
indicates that none of the
reception operations were successful.
• To return to the Timekeeping Mode, press
D
twice.
To turn auto receive on and off
1. Enter the Receive Mode (page E-24).
2. Hold down
E
until
On
or
OFF
fl ashes on the digital display. This is the
setting screen.
• Note that the setting screen will not appear if the currently selected
Home City is one that does not support time calibration reception.
3. Press
A
to toggle between auto receive on (
On
) and off (
OFF
).
4. Press
E
to exit the setting screen.
Hour :
Minutes
Month Day
1 second
Hour :
Minutes
Month Day
1 second
On/Off
status
On/Off
status
E-22
Radio-controlled Atomic Timekeeping Precautions
• Strong electrostatic charge can result in the wrong time setting.
• Even if a receive operation is successful, certain conditions can cause the time setting to be off by up
to one second.
• The watch is designed to update the date and day of the week automatically for the period January 1,
2000 to December 31, 2099. Updating of the date by signal reception will no longer be performed
starting from January 1, 2100.
• If you are in an area where signal reception is not possible, the watch keeps time with the precision
noted in “Specifi cations” (page E-103).
• The receive operation is disabled under any of the following conditions.
– While power is at Level 3 (
L
) or lower (page E-11)
– While the watch is in the power recovery mode (page E-12)
– While a sensor operation is being performed
– When the watch is in the function sleep state (“Power Saving”, page E-14)
– While a hand home position adjustment operation is in progress (page E-86)
– While a countdown timer operation is in progress (page E-77)
• A receive operation is cancelled if an alarm sounds while it is being performed.
• The Home City setting reverts to the initial default of
TOKYO
(
TYO
) whenever the battery power level
drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the
Home City to the setting you want (page E-28) .
E-23
Mode Reference Guide
Your watch has 11 “modes”. The mode you should select depends on what you want to do.
To do this: Enter this mode: See:
• View the current date in the Home City
• Confi gure Home City and daylight saving time (DST) settings
• Confi gure time and date settings manually
Timekeeping Mode E-27
• Determine your current bearing or the direction from your current
location to a destination as a direction indicator and angle value
• Determine your current location using the watch and a map
Compass Mode E-34
• View the barometric pressure and temperature at your current location
• View a graph of barometric pressure readings
Barometer/Thermometer
Mode
E-44
• View the altitude at your current location
• Determine the altitude differential between two locations (reference
point and current location)
• Record an altitude reading with the measurement time and date
Altimeter Mode E-52
Recall records created in the Altimeter Mode Data Recall Mode E-72
Use the stopwatch to measure elapsed time Stopwatch Mode E-75
Use the countdown timer Countdown Timer Mode E-77
Set an alarm time Alarm Mode E-79
View the current time in one of 29 cities (29 time zones) around the globe World Time Mode E-82
• Perform a time calibration receive operation
• Check whether the last receive operation was successful
Receive Mode E-20
Perform hand home position adjustment
Hand Home Position
Adjustment Mode
E-86