Filter
Top Products
Operation Guide 3311/3356
8
7. While the day of the week
setting is flashing, press
the
DD
DD
D button to toggle it
between Japanese (kanji)
and English.
8. While the Power Saving
setting is flashing, press
the
DD
DD
D button to toggle it
on (ON) or off (OF).
Use the C button to select each of the settings and the D
and B buttons to change them.
9. When all of the settings
are the way you want,
press the
AA
AA
A button.
• This exits the setting screen.
• The display also will exit the
setting screen automatically if
you do not perform any
operation for about two or
three minutes.
5. To restart the seconds
count to 00, press the
DD
DD
D
button.
• While the seconds are
selected, press the D button
to reset them to 00 in
accordance with the time
signal on the radio, TV, etc.
• Pressing the D button while the seconds count is in the range
of 30 to 59 resets it to 00 and also adds 1 to the minutes.
Pressing the D button in the range of 00 to 29 resets the
seconds count without changing the minutes.
• Pressing the B button while the seconds count is flashing
changes the display illumination duration. See “To specify
display illumination duration” for more information.
6. While the hour, minutes,
year, month, or day setting
is flashing, use the
DD
DD
D (+)
and
BB
BB
B (–) buttons to
change the setting.
• Holding down either button
changes the setting at high
speed.
• When setting the hour, make sure you specify AM (no
indicator) or PM (P) correctly, or that you specify the correct
24-hour time.
• You can set a date in the range of January 1, 2000 to
December 31, 2099.
• The day of the week is set automatically in accordance with
the date you set.
• The watch automatically makes adjustments for leap years
and month lengths.
3. Press the
CC
CC
C button so the
setting you want to
change is flashing on the
display.
• Use the C button to cycle
through the settings shown
below. Each press of the C
button causes the next setting
to flash.
Language
Day
Minute
Hour
Second
Year
Month
Power Saving
12/24-hour
Timekeeping
4. While the 12/24-hour
timekeeping setting is
flashing, press the
DD
DD
D
button to select the
setting you want.
• Pressing the D button
toggles the timekeeping
format between 12-hour (12H)
and 24-hour (24H).
❚
To configure digital settings
1. In the Timekeeping Mode
hold down the
AA
AA
A button
for about two seconds.
• This will display the
transmitter selection mode
setting screen and cause the
second hand to move to the
12 o’clock position.
2. Press the
AA
AA
A button to
advance to the next group
of settings.
• This causes the 12/24-hour
timekeeping setting to flash.
Example: 12H (12-hour timekeeping)
❚
Elapsed Time Measurement
Start Stop Reset
Pressing the A button while timing is stopped resets the stopwatch to all zeros.
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting it to all zeros causes the elapsed time measurement to resume from
where it was last stopped.
❚
Split Time Measurement
Start Record Split Clear Split Stop Reset
Pressing the A button while timing is being performed displays the split time screen, but timing continues internally.
• Changing to another mode while a split time is displayed clears the split time operation.
❚
1st and 2nd Place Finishers
Start 1st Finish
(Displays time of 1st finisher.)
2nd finish Displays time of 2nd finisher. Reset
Pressing the D button while the split time screen is on the display stops elapsed time measurement, and leaves the split time screen on
the display. Press the A button to exit the split time screen and display the elapsed time when the measurement was stopped.
Split Time Screen
The split time screen cycles alternately cycle through
the split indicator, a minute/second screen, and a
1/100 second screen.
• Displays Setting Screen
• Changes Setting Group
• Exits Setting Screen
(Selects Setting)
You can select either Japanese (kanji) or English for the day of the
week indicator.
• For more information, see “To configure digital settings”.
Day of the Week Indicators
Sunday: SU/ Monday: MO/ Tuesday: TU/
Wednesday: WE/ Thursday: TH/ Friday: FR/
Saturday: SA/
See “Signal Reception Settings” for information about
calibration signal, Home City, summer time, and auto
receive settings.
If you are planning to manually adjust both the digital and analog settings, be sure to adjust the digital setting first.
Time and Date Settings
Timekeeping Mode
Language
Day
Minute
Hour
Seconds
Auto Receive
Transmitter Selection
Mode
Summer Time
Home City Code
(Hold down about two seconds.)
Year
Month
Power
Saving
12/24-hour
timekeeping
• While the setting screen (the one with a flashing setting) is on the
display, use the C and A buttons to move the flashing between
settings.
Configuring Time and Date Settings Manually
(Zero Reset)
(Back)
(Forward)
Japanese (Kanji)
(To
gg
les)
(To
gg
les)
(Enters/Exits Setting Screen) (Scrolls Back)
(Scrolls Forward)
(Chan
g
es Selection)
Timekeeping Mode
(Changes Setting Group)
(Selects Settin
g
)
(To
gg
les)
Split Indicator
1/100 Second
Minutes Seconds