Filter
Top Products
Operation Guide 3311/3356
7
5. Use the
DD
DD
D (+) and
BB
BB
B (–)
buttons to change the
minute setting.
• Holding down either button
changes the setting at high
speed.
6. When the setting is the
way you want, press the
AA
AA
A button.
• This exits the setting screen.
• The display also will exit the
setting screen automatically if
you do not perform any
operation for about two or
three minutes.
❚
To set an alarm time
Example: To set Alarm 2 for 3:30 p.m.
1. In the Alarm Mode, use the
DD
DD
D button to scroll
through the alarm screens
until the one whose
setting you want to
change is displayed.
• An alarm number (AL1, AL2,
AL3) indicates the current
screen.
2. Hold down the
AA
AA
A button
for about two seconds.
• This will cause the hour digits
of the displayed alarm time to
flash.
• Displaying the setting screen
automatically turns on the
displayed alarm.
3. Use the
DD
DD
D (+) and
BB
BB
B (–)
buttons to change the
hour setting.
• In this example, set the hour
digit to 3 p.m.
• Holding down either button
changes the setting at high
speed.
• When setting the hour, make
sure you specify AM (no
indicator) or PM (P) correctly
when using 12-hour
timekeeping, or that you
specify the correct 24-hour
time.
• The same 12-hour/24-hour
format you select for the
Timekeeping Mode time is
also applied in the Alarm
Mode.
4. Press the
CC
CC
C button to
select the minute setting.
• This causes the minute digits
to flash.
(Selects Alarm)
Hour
(Setting Screen)
(Forward)
(Back)
(Selects Settin
g
)
Minutes
You can set the daily alarms in 1-minute increments. The watch
beeps for 10 seconds when the current time in the Timekeeping
Mode reaches the alarm time you set. There are three
independent alarms, and all of them operate the same way.
The Hourly Time signal causes the watch to beep every hour on
the hour.
When you enter the Alarm Mode, the screen for the alarm that was
displayed when you last exited the mode appears first.
(3 times)
Alarm Time
Alarm Number
Timekeeping Mode
2-second
interval
❚
To select an alarm or the Hourly Time
Signal screen
Each press of the D button cycles through available screens in
the sequence shown below.
Alarm 1 Alarm 2
Alarm 3Hourly Time Signal
Using the Alarms and Hourly Time Signal
❚
To turn an alarm or the hourly time
signal on or off
1. In the Alarm Mode, use the
DD
DD
D button to display the
screen for the setting you
want to turn on or off.
• Each press of the D button
advances to the next alarm,
which is indicated by the
alarm number on the display.
2. Press the
AA
AA
A button to toggle the currently displayed
alarm on or off.
Alarm
(On/Off)
Hourly Time Signal
(On/Off)
❚
To stop the alarm beeper
Press any button.
❚
To test the alarm
In the Alarm Mode, hold down the D button to sound the alarm.
The stopwatch measures elapsed time in units of 1/100 second up to 99 minutes, 59.99 seconds (100 minutes total). When the maximum
limit is reached, the elapsed time automatically returns to zero and timing continues from there.
❚
Display Screen Switching
• Elapsed Time Screen
A 1/100 second value is displayed for the first minute after you
start an elapsed time measurement. After the first minute, the
screen changes automatically to show elapsed minutes and
seconds.
1/100 Second
Seconds
Seconds
Minutes
Minute and Second Screen
• Paused Elapsed Time Measurement Screen
When elapsed time measurement is paused, the display alternates
between a minute/second screen and a 1/100 second screen at
1-second intervals.
Second
Minutes
1/100 Second
(4 times)
Mode Indicator
Timekeeping Mode
About two
seconds
AA
AA
A Button
Split/Reset
• Press during elapsed time measurement to display the split
time.
• Press when elapsed time measurement is stopped to reset
the stopwatch to all zeros.
DD
DD
D Button
Start/Stop
• Each press starts and stops elapsed time measurement.
Stopwatch Mode
(Forward)
(Back)
(Selects Alarm)
Alarm Number