05-04-06
CA100
2
Exit:
Turn Ignition to 'OFF' position, or leave it for 15 seconds. Three long chirps & Three parking light flashes
confirm exit.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch
2
times and holding in on
2
nd
push until
one
short chirp with one long chirp is heard
then release the valet switch. You are now in the Alarm feature
‘I’
programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change.
a.
The siren chirps and LED pause will indicate new setting.
b.
The system would advance to [2] LED flash, [2] chirp. (The factory default setting is always [1] LED flash,
[1] chirp.)
4 Depress the transmitter button ‘A’ again to change the feature again. Simply keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
1
Chirps on Chirps off
2
Automatic Rearm On Automatic Rearm Off
3 +
Instantly Door Ajar Warning. 45 seconds Delay Door Ajar error chirp.
Exit
:
Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
ALARM FEATURE “
II
” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch
4
times and holding in on the
4
th
push until
two
chirps with a long chirp is heard then
release the valet switch. You are now in the Alarm feature
‘II’
programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
1
0.9-second Door lock
pulses.
3.0-second Door lock pulse. Double pulse unlock
2
Active arming Passive arming without
passive door locking
Passive arming with passive
door locking.
3 +
Ignition controlled door locks
& unlocks
Without ignition controlled
door locks & unlocks
Exit
:
Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
ALARM FEATURE “III” PRORAMMING:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch
6
times and holding in on the
6
th
push until three chirps with a long chirp is heard
then release the valet switch. You are now in the Alarm feature ‘III’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
1
Shock Sensor Program Mode
2
Tan Wire = Trunk (Channel 3) Output Gray Wire = Two Step Door Unlock Output
3 +
Car Jacking Off Car Jacking On
Exit
:
Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
ADJEST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6 times and holding in on the 6th push until three chirps with a long chirp is heard then
release the valet switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode.
3. Press and hold
button for 2 seconds. One long siren chirp to indicate the unit is ready to accept
adjustments for the
second stage of the shock sensor (full alarm).
4. Press
button on the transmitter once will decrease sensitivity level by one, each time an decrease is
made the siren chirp will respond with [1] chirp, while 2 chirp indicates the minimum of sensitivity.
5. Press
button on the transmitter once will increase sensitivity level by one, each time an increase is made
the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates the maximum of sensitivity.
