1
PRO-9744
The PRO-9744 Remote Control Security System has been designed as a completely configurable system that will
meet the needs of any consumer. In addition to the many programmable features of the unit, the system offers a
transmitter membrane button replacement program. This will allows you to configure the button's of the transmitter
to coincide with configured operation of the system.
INSTALLATION OF THE MAJOR COMPONENTS:
CONTROL MODULE:
Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location
selected must insure that the module will not interfere with proper operation of the vehicle. Avoid mounting the
module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or block
the steering wheel preventing proper control of the vehicle. Secure the module in the chosen location using cable
ties or screws as necessary.
Do Not Mount The Module In The Engine Compartment, as it is not waterproof.
SIREN:
Select a location in the engine compartment that is not accessible from below the vehicle. The selected location
must be clear of hot or moving parts within the engine compartment. The siren must be pointed downward to prevent
water retention, and the flared end must be pointed away and out of the compartment for maximum sound distribu-
tion. Before securing the siren, check behind your chosen location to assure that the mounting screws will not
penetrate any factory wiring or fluid lines. Secure the siren mounting bracket using #8 self taping screws or by first
using the mounting bracket as a template, scribe or mark the three bracket mounting holes. Drill the three marked
holes using a 1/8" drill bit, then mount the siren using #8 sheet metal screws.
HOOD AND TRUNK PIN SWITCHES:
The pin switches included in this package are intended for protecting the hood and trunk areas of the vehicle. In all
cases, the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood/trunk
open), it will supply a ground to the input wire activating the alarm. Mount the switches in the hood and trunk
locations away from water drain paths. If necessary, the included brackets may be used to move the switch away
from rain gutters or allow mounting to the firewall behind the hood seal. In both cases the switch must be set to allow
the hood or trunk door to depress the switch at least 1/4 inch when the hood or trunk is closed and, fully extended
when the hood or trunk is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind the
chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the
desired location and thread the pin switch into it using a 7/16" nut driver or deep well socket. If using the mounting
bracket, first secure the bracket to the desired location and secure the pin switch in the pre-threaded mounting
bracket hole.
DASH MOUNTED L.E.D.:
The small Red LED included in the kit will serve as a visual indicator of the alarm's status and provide a visual
deterrent to a potential thief. The LED also provides important feed back information during the transmitter and
feature program modes. The LED should be installed in the dash in an area highly visible so that it may be seen from
the drivers seat as well as from outside the vehicle. Inspect behind the chosen location to insure that the drill will not
penetrate any existing factory wiring or fluid lines. Carefully drill a 1/4" hole in the desired location and pass the
connector end of the LED through the hole and toward the control module. Press the LED firmly into place until it is
fully seated in the mounting hole.
VALET / PROGRAM / MANUAL OVERRIDE SWITCH :
Select a mounting location that is easily accessible to the operator of the vehicle. It is not necessary to conceal the
switch however concealment is recommended as it offers a higher level of security. The switch can be mounted to
the lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is
allowed for the body of the switch, as well that the drill will not penetrate any existing factory wiring or fluid lines. Drill
a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside. Secure
the switch using the nut, star washer, and on/off face plate. It is suggested that the switch be oriented to allow the on
position to be up toward the driver and the off position to be down or away from the driver. Route the switch's
connector toward the control module.
