NAMES OF CONTROLS
1. Cassette deck operation controls
STOP
F.FWD
REW
PLAY
RECORD
2. DISPLAY
3. TUNING/CD SKIP buttons
4. Cass compartment
5. MEMORY button
6. FUNCTION selector (CD/Radio/
Tape)
7. VOLUME control
8. Handle
9. CD door
10.Telescopic Antenna
11.CD PLAY/PAUSE & STOP button
12.REPEAT button
13.PRESET button
14.BAND button
15.POWER ON/OFF switch
16.PHONES jack
17.AC socket
18.Battery compartment
- 1 -
AC POWER
You can power the unit by plugging the
detachable AC power cord into the AC
inlet on the back of the unit and wall AC
outlet.
Check that the rated voltage of your unit
matches your local voltage.
Make sure that the AC power cord is fully
inserted into the unit.
CAUTION:
To prevent electrical shock, match wide
blade of plug to wide slot, fully insert.
POWERING UP
BATTERY POWER
Insert 8 "C" size batteries in
the
battery compartment. Be sure
that the batteries are inserted
correctly to avoid damage to
the unit.
Cautions:
Do not mix old and new
batteries.
Do not mix alkaline, standard
(carbon-zinc), or rechargeable
(nickel-cadmium) batteries.
Be sure to install the battery before disconnecting the AC power cord.
Always remove the batteries when unit will not be used for a long
period of time, as this will cause leakage to the batteries and subsequently
damage to your unit.
TO TURN ON/OFF THE UNIT
To turn on the unit, slide the POWER switch to ON position.
To turn off the unit, slide the POWER switch to OFF position.
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
MANUAL TUNING
You can listen to your favourite radio stations by sliding the FUNCTION selector
to RADIO, and then
1. Press the BAND button to select the desired band.
2. Press the TUNING +/- buttons to select a station.
3. Adjust the volume.
AUTOMATIC SEARCH TUNING
Press the TUNING + or - button until the ' ' appears, and
a station is searched automatically. When the search is at the
end of the band acceptance level is decreased.
FOR BETTER RECEPTION
FM
Extend and rotate the antenna
to get better FM reception.
AM(MW)
Rotate the unit to get the best
receiving position.
PRESETTING STATION
You can tune into a stored station directly by entering the preset number.
1. Press the BAND button to select a band and tune the TUNING + / - buttons
to choose a desired station.
2. Press the MEMORY button, "MEMORY" indicator will blink on the display.
3. Press the PRESET button to preset a number.
4. Press the MEMORY button again to store the frequency under the selected
preset number.
5. Then, repeat steps 1 to 4 to for next preset.
TUNING INTO A PRESET STATION
Press the PRESET button to select a presetted number.
1. Slide the FUNCTION selector to CD. " " is shown on the
display.
2. Open the CD door. Place a disc in the center with the label side front and
then close the CD door gently.
The total number of tracks and playing time will show on the display.
3. Press the PLAY/PAUSE button to start CD play.
TO STOP PLAYBACK
Press the STOP button to stop disc play.
TO INTERRUPT PLAYBACK
Press the PLAY/PAUSE button while a CD is playing to pause play ( " "
indicator will light up).
Press the PLAY/PAUSE button again to resume play.
TO SKIP TO THE BEGINNING OF A TRACK
Pressed either one of the SKIP or button according to the desired
direction, each press skips one track.
Playback resumes from the selected track.
USING THE CD PLAYER
REPEAT PLAY (IN PLAY MODE)
This function allows one track, all tracks on a disc or the programmed tracks
only to be played repeatedly.
TO REPEAT THE SAME TRACK
Press the REPEAT button once during playback, "REPEAT" will light up on
the display.
TO REPEAT THE WHOLE DISC
Press the REPEAT button a second time to repeat all tracks, "REPEAT"
indicator will blink on the display.
TO CANCEL REPEAT PLAY
Press the REPEAT button until "REPEAT" indicator is disappeared on the
display.
OR
Press the STOP button.
Note:
After listening, slide the POWER switch to OFF position.
MEMORY PLAY (IN STOP MODE)
1. Press the MEMORY button, "MEMORY" indicator will blink on the display.
2. Press the SKIP or SKIP button to select the desired track.
3. Press the MEMORY button to program a track.
4. Repeat steps 2 and 3 until all the desired track are programmed (up to 12
tracks).
5. Press the PLAY/PAUSE button. During program playback, "MEMORY"
indicator will light up.
If an attempt is stored more than 12 tracks, " " is displayed.
TO PLAY THE PROGRAMMED TRACKS
After storing the desired tracks, press the PLAY/PAUSE button to play the
program.
TO STOP PROGRAMMED PLAY
Press the STOP button to stop playback.
TO CLEAR THE PROGRAM
Press the STOP button twice, open the CD door or slide the FUNCTION
selector to TAPE or RADIO to clear the program.
Note:
Programming can only be done when the unit is in the stop mode.
TO ADJUST THE VOLUME
Adjust the VOLUME control to obtain the desired volume level.
WHEN RECORDING
The VOLUME control may be adjusted with no effect on the recorded signal.
FOR PRIVATE LISTENING
Connect headphones (Ø3.5mm stereo mini-plug) to the PHONES jack. When
the headphones are connected, speakers automatically disconnect.
J
ADIUSTING THE SOUND
TO WALL AC OUTLET
TO AC INLET
RADIO OPERATION
.5V1
.5V1
.5V1 .5V1
1.5V1.5V
11.5V .5V
