Filter
Top Products
6.1 SPOTLIGHT BULB REMOVAL PROCEDURE
1. Rest the unit on a secure tabletop.
2. Position the head to be in the Spotlight position.
3. Lift off the rubber Safety Ring and set it aside.
4. Grasp the Retaining Ring and rotate it slightly clockwise until the
ring’s tab lines up with the notch in the head.
5. Lift off the retaining ring.
6. Pull the lens, “O” ring and reflector assembly from the head.
7. Set the lens and “O” ring aside.
8. The Reflector/Lamp Assembly should be hanging from the two wires.
9. On the Reflector Assembly, carefully squeeze the two retaining wires
together and lift them to release them from the “T” slot.
10. Loosen the screw—item #11.
11. Rotate the two retaining wires upward as shown, to allow the bulb to lift out.
12. Disconnect the white wire by pulling apart the two connectors on the wire.
13. Follow local procedures for bulb disposal.
6.2 SPOTLIGHT BULB INSTALLATION PROCEDURE
1. Insert the new bulb in the Reflector/Lamp Assembly.
2. Rotate the two retaining wires downward as shown, to hold the bulb in place.
3. Tighten the screw— item #11.
4. Connect the white wire by pushing together the two connectors.
5. On the reflector Assembly, carefully squeeze the two retaining wires together
and place them in the “T” slot.
6. Replace the Reflector/Lamp Assembly, “O” Ring and Lens.
7. Place the Retaining Ring so that it’s tabs are aligned with the notches in the head.
8. Press the Retaining Ring until it is fully seated and rotate it slightly counter clock–
wise to secure it against the head.
9. Replace the rubber Safety Ring by pushing it onto the Retaining Ring. Make
sure the Safety Ring is fully seated.
Open
Closed
34
AC AND DC RECHARGE ADAPTERS
FIGURE 2A FIGURE 2B
4.1 AC RECHARGE
The AC Recharge adapter provides 300 mA at 12 Volts DC for recharging the
batteries. Power the AC Recharger from a standard, 110 volt, 60 Hz AC North
American receptacle. The AC recharger will not support lamp operation. Do
not operate the lamps while the AC Recharger is connected to the Recharge
Port. Charge with lamps Off until LEDs are equally bright. This steady recharge
will prolong battery life. Only use the supplied AC Recharger—DO NOT
SUBSTITUTE WITH ANOTHER. SEE FIGURE 2A
4.2 DC RECHARGE/OPERATION
The DC Recharge adapter provides 12 Volts DC for simultaneously recharging
the batteries and operating either light. Power the DC Recharger from a stan-
dard, 12-volt DC cigarette lighter type accessory socket. Charge until LEDs are
equally bright. After recharge, either disconnect the DC recharger or leave
connected and continue to operate either light. Only use the supplied DC
Recharger - do not substitute with another. The DC Recharge Adapter’s DC Plug
is equipped with a user-replaceable 10-ampere fuse. SEE FIGURE 2B
5. MAINTENANCE/PARTS REPLACEMENT
If the unit has dirt on it, gently clean the outer surfaces of the SportSpot Lantern
with a soft cloth moistened with a mild solution of water and detergent.
Periodically inspect the condition of recharge adapters, connectors, and wires.
Replace any components that may have become worn or broken.
Four parts are replaceable by users. The quartz halogen bulb and the fluorescent
tube are proprietary and are only available through Vector Manufacturing. The
sealed lead acid battery and fuse are available from Vector as well as from popular
automotive parts suppliers nationwide. Contact Vector Manufacturing’s Technical
Support Department for replacement parts and any additional information that you
may need. They may be reached at (954) 584-4446.
6. SPOTLIGHT BULB REPLACEMENT
See Figure 3 for bulb removal and replacement. Make sure that the On/Off
Switch is Off and disconnect the battery. SEE SECTION 9.
SPOTLIGHT BULB REMOVAL / INSTALLATION
FIGURE 3
DC RECHARGEABLE
ADAPTER
FUSED DC PLUG
BARREL CONNECTOR
AC RECHARGEABLE
ADAPTER
1. SAFETY RING
2. RETAINING RING TAB
3. RETAINING RING LENS
4. LENS
5. O-RING
6. REFLECTOR/LAMP ASSEMBLY
7. NOTCH
8. RETAINING WIRES
9. WHITE WIRE
10. GREEN OR BLACK WIRE
11. SCREW
2
3
4
1
7
65
Open
Closed
8
9
10
11
11
9
10